9308 EVERGREEN WAY 2016-01-01 MF Import

Chepler A. Accessible Routes 404.2.7 Closing Speed. 404.2.7.1 Door Closers. Door closers shell be adjusted so thet irom an open positlon of 90 degrees, the time required to move ihe door to an open position of 12 degrees shall be 5 seconds minimum. 404.2.7.2 Spring Hinges. Door spring hinges shell be adjusted so ihal irom the open position of 70 degrees, ihe door shell move to the closed position in 1.5 seconds minimum. 404.2.8 Door-Opening Force. Flre doors shall have the minimum opening force allo�vable by the approprfale administrative authority. Tha forco for pushing or pulling open doors other than fire doors shall be as follows: 1. Interior hfnged door: 5.0 pounds (22.2 N) meximum 2. Sliding or tolding door: 5,0 pounds (22.2 N) maximum These iorces do not epply to ths torco required to retract letch bolts or disengage olher devices that hold the door in a closed posilion. 404.2.9 Door Surface. Door surfacos wi�hin 10 inches (255 mm) oithe iloor, measured verlical- ly, shall be e smooth surface on lhe push side extending the full width of the door. Paris creat- ing horizontal or vertical Jofnts in such surface shell be within �/16 (nch (1.6 mm) oi tha same plane as ihe other. Cavities created by added kick plates shall be capped. EXCEPTiONS: 1. Sliding doors. 2. Tempered gless doors wilhout stiles and having a bottom rail or shoe with the top leading edge iepered at no less than 60 degrees irom the horizontel shall not be required to meet tne 10 inch (255 mm) bottom rail height requiremen!. 3. Doors that do not extend to within 10 inches (255 mm) of the iloor. A04.2.10 Vlsion Lites. Doors and sidelites ad- jacent 10 doors con;aining one or more glezing panels ihat permit viewing through the panels shall havo ihe bottom of at least one panel on either ihe door or an adjacent sidelite 431nches (1090 mm) meximum above the iloor. EXCEPTION: Vislon lites with the lowest part more than 66 inches (1675 mm) ebove ICC/ANSI A117.1-20D3 the iloor are not required to comply with Section 404.2.10. 404.3 Automatic Doors. Automatic doors and au- tomaiic gates shall comply witli Section 404.3. Full powered automaiic doors shell comply with ANSI/ BHMA A156.10 Iisted in Section 105.2.4. Power- essist ond low-energy doors shell comply with ANSI/BHMA A156.19 listed in Section 105.2.3. EXCEPTION: Doors, doorways, and gates de- signed to be operated only by security personnel shall not be required to comply with Sections 404.3.2, 404.3.4, and 404.3.5. 404.3.1 Clear Opening Wldth. Doonvays shall have a clear opening widih of 32 inches (815 mm) in power-on and power•off mode. The minfmum clear opening width for automatic door systems shell be based on the cleer opening width provided with all leafs in tha open positfon. 404.3.2 Maneuvering Clearances. Maneuver- ing clearances at power-assisted doors shall comply with Sectian 404.2.3. 404.3.3 Thresholds. Thresholds and changes in level at doorways shall comply with Sectlon 404.2.4. 404.3.4 Two Doors in Serles. Doors In series shell comply with Section 404.2.5. 404.3.5 Control Switches. Manually operated controi switches shall comply with Seclion 309. The clear iloor space adJacent to the control switch shall 6e located beyond ihe erc oi the door swing. 405 Ramps 405.1 General. aamps alorg accessible routes shell comply wilh Seclion 405. 405.2 Slope. Ramp runs shall have e running slope not steeper than 1:12. EXCEPTION: In exisiing buildings or facilities, remps shall be permitter! to have slopes steeper than 1:12 complying witn Table 405.2 where such slopes aro necessary due tu spece limitafions. 405.3 Cross Slope. Cross slope of ramp runs shall not be steeper ihan 1:48. 405.4 Floor Surfaces, Floor surtaces of ramp runs shall comply wiih Section 302.