4526 FEDERAL AVE 2018-01-02 MF Import

15. Exterior (court) walls wit u% ..... . .......... feet of ✓d lines should be of ............ •hour construction. Section .................... 0 (a). 1G. Openings in exterior (court) walls within ............ feet of properly lines should be protected will% three -fourths -hour fire assemblies. Section .................: 03 (b). 17. Usable space under the first floor except in Group I (J) Occupancies should be enclosed as required in Section 1703. 18. Fire -resistive construction for structural elements in the exterior walls should comply with Foot. note No. 1 of Table No. 17•A and Section ..................... See Section 1702 for clarification. 19. Building paper should be applied to exterior walls as specified in Section 1707 (a). 20. Enclosures for floor openings should comply with Table No. 17-A, Section 1706, and Chapter 30. Details should clearly indicate this. 21. Structural members carrying masonry or con• crete walls in buildings over one story in height should be protected with minimum one -hour fire protection. Section 1708. ............................................................................ 22. Nonabsorbent finish and backing for toilet room walls and floor should conform with Soclion 1711 (a). 23. Shower stall walls should be finished with a hard, nonabsorbent surface to a height of G feet. Section 1711 (b). 24. Doors andpanels of shower and bathtub en• closure should comply with Section 1711 (c) to (o). 25. Parapet walls not less than ................ inches in height are required. Section 1709. 2.6. Eave overhangs and similar architectural pro. Jections should comply with Section 1710. 27. Metal roofing (sidingj�,slfould be bonded and grounded in conformance with the local elec- trical code. Seclion,1715. 28. Projections beyond the exterior wall should con. '4 form with the least restrictive of the following: (a) A point one-third the distance to the property line from an exterior wall. Section 504 (b). (b) A point one-third the distance from on as• sumed vertical plane located where 'lire• resistive protection of openings is first re- quired due to location of properly. Section 5C4 (b). 29, Envelope ceilings should satisfy the following conditions )Section 4303 (b) 6.1: (a) Should not bo used to provide fire protection beam and girders supporting more than one floor. (b) Columns should be inrtividnally fire protected. (e) Duct and outlet openings are limited to 100 square inches in each loo square feet of ceiling area and should be protected with approved fire dampers. (d) Electrical outlet boxes should be of steel and not greater than 16 square inches in area. 30. Gypsum board ceilings in conjunction with fire• resistive, assemblies should be supported at intervals not exceeding 16 inches. Item 25, Table No. 43•C. 31. Wood strillpintf or sesponded wand systems for board ceilings should be flat less than gypsum 2.•inch nominal thickness. Section 4704 (b)• j Scchon n702. (b) for Will stripPing.) layouts and details should be sub - 32. Final nartitinn tsttructural,iaa d sf tares will, occu fluty t ve exit requirements. 33. Justifying test data in conformance with Section 10G or an ICBO research recoil, mendat ion is .required for ....................................................... 34. Rooms in which rubbish (linen) chutes terminate should be separated from the remainder of the building with a one -hour occupancy separation. Section 3003. 35, Openings into rubbish and linen chutes should not be located In required exit corridors or stair- ways. Section 3003. SPECIAL OCCUPANCY REQUIREMENTS ............................................................................ ............................................................................ Group B 36. . B-3 Occupancies should be of ono -hour fire - resistive construction if located in a basement or above lire first story. Section 702 (b). 37. B-2 Occupancies with an occupant load of 1000 or more should be in Type I, II, or III one -hour buildings. The assembly room should not be in a basement if it contains this high occupant • load. Section 702 (b). 38. The main entrance should front directly upon or have a 20-foot wide access to a public way at least 20 feet in width. Section 703. 39. Light and ventilation should comply with Section 705. 40. A one -hour fire -resistive occupancy separation is required between the boiler or central heating plant and the rest of the building. Section 703. 41. Exterior openings for roosts containing a boiler or central heating plant should be protected with three -fourths -hour fire -resistive assemblies that are fixed, automatic. or self -closing if lo. cated below openings in another story or if less than 10 feet from other doors or windows in the same building. Section 708. Group C 42. Buildings housing Group C Occupancies should be of onn•hour fireaesistive construction throughout. Section 602 (a) and Table No. S.C. 43. Use of rooms should be clarified. Note that rooms having an occupant toad of more than 100 and rooms used for kindergarten, first, or second grade cannot be located above the first story above grade except in Type I construe. tion. Section 802 (b). 44. A one -hour fire -resistive separation is required between laboratories, shop;, storage rooms. • These areas should also be separated from other classrooms. Section UO2 (b). I 45. One required exit should front directly upon, or have a 20-foot wide access to, a public way at -� least 2.0 feel in width. Section 803 (a). 46. Sanitary facilities should be provided in accord• t47. ante with Section 805. Light and ventilation should comply with Section 805. Sheet No..... ?......of........5.......... Sl,eet;