Laserfiche WebLink
2004 Washington Slate Nonresltlenlial Energy Code Compliance Form <br /> • • ' ' • • � <br /> 700a Wesnmgton Slate Nonreswer.Ual Enerpy Coae ComoL Forms RevuaC May I005 <br /> ProjectAddress eonr oe evracrr Date 3/23/2006 <br /> Space Heat Type Q Electric resistance QQ Ali other For Building Department Use <br /> Glazin E�1ed as%gross exterior wall area l�•6� P�op. 45.09 Max.Target <br /> Concrete/Masonry Option O ves O• No <br /> Notes:I(olazing area ezceeds maximum allowetl in Table,lhen calculate adjusted areas on back(oveq. If ConcretelMasonry Option <br /> is used,Targel U-factors,SHGC and Glazing%will be diHerent than shown beluw. Refer to Table 13•1 for correct values. <br /> Bullding Camponent Proposed UA Target UA <br /> List components b assembly ID 8 pa e# U-factor x Area(A) =UA(U x A1 U-factor z Area(A) =UA(U x A) <br /> U=0.550 PIanID xihmws 0.550 890.0 <89.5 0.550 090.0 <89.5 <br /> U= Plan ID: Giazing% Eleclnc ResisL Other Healing <br /> rn U= Plan ID: 0-30°h 0.40 0.55 <br /> u 5 >3D-45% see note above 0.45 <br /> r N U= Plan ID: <br /> m <br /> > C9 U= Plan ID: <br /> U= Plan ID: <br /> U= Plan ID: <br /> ;; U= Plan ID: o.�oo <br /> �' Q U= Plan ID: Glazing°h Electric Resist. Other Heating <br /> �m v U= Plan ID: 0-30% 0.6 0.7 <br /> � o �= Plan ID: >30-05% see note above 0.6 <br /> 0 <br /> 19 ,n U= Plan ID: <br /> m � <br /> t o U= Plan ID: <br /> i � <br /> O t U= Plan ID: <br /> � U= PIanID: 0.�00 <br /> � N U=0.500 PIanID pERSo:ntEL 0.500 126.0 63.0 0.600 306.0 183.6 <br /> � o U=o.Soo PIanlDovcaxenn o.500 180.0 90.o EledricResisl. OlherHealing <br /> 0 <br /> O� U= Plan ID: 0.60 0.60 <br /> � � R=20,0 PIanID: 0.050 2C18.0 120.9 0.036 2i18.0 87.0 <br /> � > = R= Plan ID: Electnc ResisL Olher Heating <br /> � � a R= Plan ID: 0.031 0.036 <br /> R= PIanID: O.Oa6 <br /> t � R= Plan ID: Electnc Resist. Other Healing <br /> � � R= Plan ID: 0.034 0.046 <br /> Fj=17.5 PIanID xu.z u/ SIDINc 0.057 3456.0 197.0 <br /> R=10.i PIanID ro�+caETE eASE 0.096 47.0 a.5 0.062 3861.0 239.0 <br /> = R=15.6 PIanID roNCnc7c Sioe 0.061 358.0 . 21.8 •• <br /> � R= Plan ID: Electnc Resist. Other Heating <br /> °' R= Plan ID: Freme-Wd 0.062 0.062 <br /> � <br /> n R= Plan ID: Frame-Mtl O.Oo2 0.709 <br /> � R= Plan ID: hlass Wall� 0.15 0.15 <br /> "Note: sum of Tarqet Areas here should equal Target Opaque Wall Area(see back) ++see mass wall Criteria <br /> R= Plan ID: . <br /> � � = R= Plan ID: . ElecMc ResisL Olher Heating <br /> o �j ; R= Plan�D: Int Ins 0.062 0.062 <br /> Nole:if insulated to levels required for oDaque walis. list above with opaque walls Ezt Ins 0.07 0.07 <br /> „ t R= PIanID: 0.056 <br /> ',L � � R= Plan ID: Electric Resist. Other Heating <br /> _ R= Pian ID: 0.029 0.056 <br /> R= Plan ID: <br /> � v ^ R=10.0 PIanID: O.SCO 197.0 106.G O.SGO 7.97.0 106.6 <br /> i � i R= Plan ID: Electric ReslsL Olher Heating <br /> � �a R= Plan ID: F=0.54 F=0.54 <br /> R= Plan ID: (see Table 13•1 for radianl ftoor values) <br /> 'For CMU walls, indiwte core insulation matenaL TOWIs 7672.0 1093.1 ToWls 7672.0 1105.9 <br /> To comply: 1)Proposed Total UA shall nol ezcoed Targot ToWI UA. <br /> 2)Proposed Tatal Area shall equal Targot Total Area. <br /> ��� <br />