|
2003 W �hin ton State Nonresiden8al Ener Code Comn��ance Fortn � .
<br /> • • ' - '
<br /> IOOI Wasninglon Slale NonresiEamial Energy COCe Canpliance Fortns R�"s����Y�4
<br /> Lighting - General Requirements 1513.5 Automatic Shut-ONControls,Extarior:Exterior
<br /> 1513 Li htin Controls. Li htin 9 P 9 9 lighting not intended far 24-hour continuous use shall be
<br /> g g g g,includin exem t li htin in automatically switched by timer,pho:ocell,or a combination of
<br /> Section 1512.shall r,omply with this section.Where occupancy timer and photocell.Automatic'�me switches musl also have
<br /> sensors are cited,they shall have the feaWres listed in Seclion program back-up capabiiities,which prevenl the loss of
<br /> 1513.6.t.Where automatic time switches are cited,they shall program and time seliin�s for at�east 10 hours,if power is
<br /> have the(eaWres listed in Section 1513.62. intenupted.
<br /> 1513.1 Local Control and A:cessi611ity: Each space, 7573.6 AutomaHc Shut-OH Controls,Interior:OKce
<br /> enclnsed by walls or ceiling-heighl partitions,shall be provided buildings greater ihan 5,000 sq.rt.and all school classrooms
<br /> with li3hting controls located within that space.The li9hting shall be equipped w!th sepa2le automalic controls to shut oN
<br /> controls,whether one or more,shall be capable of Wming off the lighting during unoccupied hours.Automatic controls may
<br /> ❑II lights within the space.The controls shall be readily be an occupancy sensor,timA switch,or other device capable
<br /> acce:�sibte,at Ihe point of entry/exit,to personnel occupying or of automatically shutting of(lighting.
<br /> usin�Ihe space.
<br /> EXCEPTIONS:The following lighting controls may be EXCEPTIONS:
<br /> centralized in remote locations: 1. Areas thal musl ba continuously illuminaled,or
<br /> 1. Lighting controls for spaces which rnust be used illuminated in a manner requiring manual
<br /> as a whole. operation of the lighting.
<br /> 2. Automatic controls. 2. Emargency lighting syslems.
<br /> 3. Conlrols requinng trained operators. 3. Switching(or industrial or manufacWnng process
<br /> 4. Controls for safetp ha>_ards and secunly. (acilities as may be required for production.
<br /> 1513.6.1 Occupancy Sensors:Occupancy sensors shall be
<br /> 1513.2 Aroa Cootrols:The maximum lic�h�ing power that may capable of automatically luming off all the lights ir.an area,no
<br /> be cenlrolled(rom a single switch or automatic conlrol shall not more than 30 minutes a%er Ihe area has been vacated.
<br /> excecd ihal which is provided by a hventy ampere circuit
<br /> loadeo to not more than eighty percenL A masler contml may 7513.6.2 Aulomatfc Time Switchas:Automatic time switches
<br /> be installed provided the individual switches relam lhEir shall have a minimum 7 day clock and 6e capable of being set
<br /> capab.,ity tn Nnclion independer�iy.Circuit breakers may not �or 7 diflerent day types perweek and incorporate an automatic
<br /> be used as the sole means of swilching, holiday"shu4ofP feaWre,which tums off all loads(or st least
<br /> EXCEPTIONS: 24 hours and then resumes normally scheduled operations.
<br /> 1. Industrial or manufacturin rocess areas,as Automatic time switches shall also have program back-up
<br /> 9 P capabilities,which prevent the loss of program and lime
<br /> may be required for production. settings(or at least 10 hours,if power is interrupled.
<br /> 2. P.reas less than five percent of footpnnt(or
<br /> footprinis over 100,000 square(eeL Automatic time switches shall incorporele an over-iide
<br /> 1513.3 Daylight Zone Control:All daylighted zones,as switching device which:
<br /> defned in Chapter 2,bolh under overhead glazing and a) is readily accessible;
<br /> adjacent to vertical glazing,shall be provided with individual b) is located so thal a person using the device can see the
<br /> controls,or daylight-or occupan4sensing automatic conirols, lights or the areas controlled by th�switch,or so ihat the
<br /> H�hich control the lights independent of general area lighling. area being illuminated is annunciated;and
<br /> Contiguous daylight zones adjacent to verti;zl glazing are c) is manually operaled;
<br /> allowed to be controlled by a single contmlling device provided d) allows the lighting to remain on for no more than two hours
<br /> that lhey do not include zones facing more Uian two adjacent `�+hen an over-nde is iniliated;and
<br /> e) controls an area not exceeding 5,000 square teet or 5
<br /> cardinal orienlations(i.e. north,east,south,wesl). Daylight percent of footprinl for(oolprints over 100,000 square feet,
<br /> zones imder overhead glazing mora than 1G feet from the whichever is greater.
<br /> perimeter shall be contmlled separately from daylight zones
<br /> adjacent to vertical glazing. 1513.7 Commissioning Requirements: For lighting controls
<br /> EXCEPTION: which include daylight or occupant sensing automatic controls,
<br /> Daylight spaces enclosed by walls or ceiling automatic shutoff controls,occupancy sensors,or automatic
<br /> heighl partilions and coniaining 2 or fewer light ��me switches,the lighling conirols shall be tested to ensure
<br /> fiztures are nol required to have a separate switch for that control devices,components,equipment and systems are
<br /> calibrated,adjusted and operate in accordanca with app�ved
<br /> general area lighting. plans and spe.:ifications.Sequences of operetion shall be
<br /> 15?3.4 Display,Exhi6itfon,and Specialty Lighting functionally tested to ensure they operale in accordance with
<br /> Controls:All display,exhibition,or specially lighting shall be approved plans and specifications.A complete report of test
<br /> conlrolled independentiy of general area lighting. procedures and results shall be prepared and filed with lha
<br /> owner. Drawing notes shall require commissioning in
<br /> accordance with this paragraph.
<br /> ��
<br />
|