Laserfiche WebLink
—CAUTION — <br />This card must he posted in a conspicuous place on the prerrises. <br />INSULATION CW tF ICUATION <br />THIS IS TO CERTIFY TnAT, IN CONFOq% ANCE WITH THE CURL D7T i HER ::AL PERFORMANCE STANDARDS (REVISED CODE <br />OF WASHINGTON, TITLE 19.27. STATE OF WASHINGTON•) AND APPROVED PLANS, INSULATION HAS BEEN INSTALLED IN <br />THE BUILDING LOCATED AT: 3215 215t r Everett <br />L OLDG. PERMIT NO. <br />ADDRESS OF PROPERTY <br />Vapor barrier at 4 mil polyethylene or equivalent must be installed in crawl space. <br />Weatherstriping, caulking, gasketing and/or other treatment to prevent air leakage must be installed around all exterior openings. <br />ROOFS <br />Type of material Manufacturer <br />IOr trade naml <br />Thickness R Value**. <br />EXTERIOR Material <br />J" L Thickness3 R Value" <br />Type of M1tatcrial Manufacturer f/rBNSL LY1211 <br />(Or trade name) (/ <br />CEILINGS <br />BATTS: Manufacturer Thickness R Value" <br />Type of Material <br />(Or trade name) <br />Sq. Ft. Covered <br />BLOWN: <br />Type of Material <br />_wt./Bag _Sq. Ft. Covered <br />FLOORS <br />Type of tdateriaJ <br />SLAB ON GRADE <br />Type of Material <br />Width of Insulation Inches <br />FOUNDATION WALLS (if required) <br />Manufacturer <br />for trade name) <br />R Value" <br />Thickness No. Bags <br />Manufacturer r<:�Thickness j i R Value"�_ <br />lOr trade name) 61 <br />Manufacturer <br />(Or trade namr <br />Type of Material Manufacturer <br />(Or trade name <br />DUCT AND/OR PIPE INSULATION <br />Type of Material Manufacturer <br />Thickness R Value•• <br />Thickness <br />Thickness <br />Generat Contractor (Builder) Contractor's Registration <br />R Value" <br />R Value" <br />By Title NO -THERM INS- IM-K --:Pr SO•N04I-2MH <br />Sub -contractor (Insulation Appticatorl Comrachr. . neguua.w„ �.umt7ar _ <br />(Insulation, Mas ry, �et�c.) (State "SAME" if same as General -Contractor) <br />BY YE Tide Date <br />"Revised Code of Washington - Thermal Performance Standards, declares: Upon completion of the installation of insulation, a card certifying <br />that the insulation has been installed in conformance with the requirements of this 1977 amendatory art shall be completed and signed by the <br />builder or insulation applicator. For this purpose, any certification card which contains all the essential data may be used. The insulation <br />compliance card shall indicate the "R" value of insulation (material only) installed in the endings, walls, floors, on the perimeter, and ducts. <br />When loose fill insulation is used the card shall show the square footage and the number and weight of bags installed to obtain the "R" value <br />listed. The card must be posted at a conspicuous location within the building and will indicate the installation date. <br />• •R Value Itheraul resistance) means the measure from the resistance of a material or building component to the passage of heat. The resistance <br />value IR) of mass type insulation shall be for the material only. "R" values shall be as listed in the current ASHRAE Handbook of Fundamentals, <br />or as tested in accordance with current applicable standards. <br />No certification of occupancy or similar certification that a newly constructed apartment house three stones Or less in height, home, or other <br />residential dwelling is habitable shall be issued by such a building department unless the structure at least s.msftes the minimum energy insulation <br />standards established mncu;mt to Ihn chanwr. <br />