3009 GEDNEY ST 2017-08-01 - Laserfiche WebLink

i �; � , ESR-1413 � Most Widely Accepted and Trusted Page 2 of 2 [0.090 inch (2.3 mm)] of wet-film thickness is required that 5.0 CONDITIONS OF USE will extend up the walls to 6 inches (152 mm) on either The RedGard° Waterproofing and Crack Prevention side. As an option, a 6-inch-wide (152 mm) section of Membrane, C-Cure Pro-Red Waterproofing Membrane fiberglass mesh, as described in Section 3.2.2., may be g63, CBP 232 Waterproofing and Anti-Fracture Membrane embedded into the membrane at corners or where floors and Jamo Waterproofing Membrane described in this and walls meet. In lieu of the roller or trowel, an airless report comply with, or are suitable alternatives to what is sprayer may be used. The sprayer must be operated specified in, those codes listed in Section 1.0 of this report, between 1900 and 2300 psi (13.10 and 15.33 MPa) to subject to the following conditions: produce a flow rate of 1.0 to 1.5 gallons (3.78 to 5.68 liter) 5.1 Application must comply with this report, the per minute; the sprayer must have a tip orifice size of manufacturer's published installation instructions and 0.025 to 0.029 inch (0.63 to 0.73 mm). A continuous flm the applicable code. In the event of a conflict between with overlapping spray must be applied. No seams are the installation instructions and this report, this report permitted. The membrane appears pink when wet and dark governs. red when dry. After the first coat has turned red, with no blushing or light pink showing (approximately 1'/2 to 5.2 Application is limited to ceramic tile and dimension 2 hours), the film must be visually inspected for integrity, stone installations on floors and for use as shower and all voids or pinholes must be filled with additional sub-pans or linings. material. A second coat must be applied at right angles to 5.3 The membrane must not be used to bridge substrate the frst. The flm thickness must also be checked expansionjoints. periodically with a wet-flm gauge. The combined frst and second coatings must be a minimum of 50 mils 0.050 inch 5.4 The membrane recognized in this report is (1.27 mm)] thick when wet and 25 mils [0.025 inch manufactured by Custom Building Products in Grand (0.64 mm)] thick when dry. A minimum of sixty minutes of Prairie, Texas under a quality control program with curing time is required after application. annual inspection by ICC-ES. 4.3 Application over Expansion Joints: 6.0 EVIDENCE SUBMITTED The membrane must not be used to bridge expansion Data in accordance with the ICC-ES Acceptance Criteria joints. When applied over expansion joints, the joint must for Waterproof Membranes for Flooring and Shower Lining be cleaned, and an opened or closed-cell backer rod is (AC115), dated June 2003 (editorially revised August installed to proper depth as specified by the designer. A 2013) and American National Standard Specification for sealant must be compressed into the joint, coating the Load Bearing, Bonded, Waterproof Membranes for Thin- sides and leaving the joint flush with the surface. After the Set Ceramic Tile and Dimension Stone Installation sealant is dry, bond breaker tape specifed by the (A118.10), dated 2014. manufacturer must be placed over the joint. Two coats of mernbrane inust be applied at a minimum of 25 mils [0.025 7•0 IDENTIFICATION inch (0.64 mm)] wet-film thickness per coat over the joint Containers of the RedGard" Waterproofing and Crack and substrate following the instructions in Section 4.2 of Prevention Membrane, C-Cure Pro-Red Waterproofing this report. The tiles or stones are then applied over the Membrane 963, CBP 232 Waterproofing and Anti-Fracture membrane, leaving a gap over the joint as specified by the Membrane and Jamo Waterproofing Membrane described designer. After the work is set, the joint must be flled as in this report are identified by a label bearing the specified by the designer. manufacturer's name (Custom Building Products) and 4.4 Method of Repair: address, the product name, the date of manufacture and the evaluation report number(ESR-1413). The membrane in the area requiring repair must be removed and the area cleaned, allowing for a minimum 2-inch (51 mm) overlap. Two coats of inembrane must be applied as described in Section 4.2 of this report. �./ ��U �