3025 LOMBARD AVE 2017-08-02 - Laserfiche WebLink

2006 Washington State Nonresidential Energy Code Compliance Form : • • ' ' ' 2006 Washington State Nonresidential Energy Code Compliance Forms Revised July 2007 ProjectAddress Everett Senior Activity Center Date 6/5/2009 The following information is necessary to check a building permit application for compliance with the building envelope requirements in the Washington State Nonresidential Energy Code. Applicability Code Location Building Department (yes, no, n.a.) Section Component Information Required on Plans Notes GENERAL REQUIREMENTS (Sections 1301-1314) 1301 Sco e Unconditioned s aces identified on lans if allowed yes 1302 Space heat type: rr3.i Other If"Othel", M3.2 indicate on lans that electric resistance heat is not allowed n.a. 1310.2 Semi-heated spaces Semi-heated spaces identified on plans if allowed 1311 Insulation yes 1311.1 Insul.installation Indicate densities and clearances spec yes 1311.2 Roof/ceiling insul. Indicate R-value on roof sections for attics and other roofs; r+6.o Indicate clearances for attic insulation; Indicate baffles if eave vents installed; Indicate face sta lin of faced batts yes 1311.3 Wali insulation Indicate R-value on wall sections; A5.0 Indicate face stapling of faced batts; ' Indicate above grade exterior insulation is protected; Indicate loose-fill core insulation for masonry walis as necess; Indicate heat capacity of masonry walls if mason o tion is used F73 yes 1311.4 Floor insulation Indicate R-value on floor sections; A5.1 Indicate substantiai contact with surface; Indicate supports not more than 24"o.c.; Indlcate that insulation does not block airflow throu h foundation vents n.a. 1311.5 Slab-on-grade floor Indicate R-value on wall section or foundation detail; Indicate siab insulation extends down vertically 24"from top; Indicate above rade exterior insulation is rotected n.a. 1311.6 Radiant floor Indicate R-value on wall section or foundation detail; Indicate slab insulation extends down vertically 36"from the top; Indicate above grade exterior insulation is protected; indicate insulation also under entire slab where re 'd.b Official yes 1312 Glazing and doors Provide calculation of glazing area(including both verticai A6.1 vertical and overhead as ercent of ross wall area yes 1312.1 U-factors Indicate glazing and door U-factors on glazing and door spec schedule(provide area-weighted calculations as necessary); Indicate if values are NFRC or default,if values are default then specify frame type,glazing layers,gapwidth,low-e coatin s as fillin s yes 1312.2 SHGC&SC Indicate glazing solar heat gain coefficient or shading spec coe�cient on glazing schedule(provide area-weighted calculations as necessa 1313 Moisture control yes 1313.1 Vapor retarders I�dicate vapor retarders on warm side spec yes 1313.2 Roof/ceiling vap.ret. Indicate vapor retarder on roof section; A6.0 Indicate va .retard.with sealed seams for non-wood struc. yes 1313.3 Wali vapor retarder Indicate vapor retarder on wall section A5.0 yes 1313.4 Floor vapor retarder Indicate vapor retarder on floor section A6.0 n.a. 1313.5 Crawi space vap.ret. Indicate six mil black polyethylene overlapped 12"on ground 1314 Air leakage yes 1314.1 Bidg.envel.sealing Indicate sealing,caulking,gasketing,and weatherstripping spec yes 1314.2 Glazing/door sealing Indicate weatherstripping spec yes 1314.3 Assemb.as ducts Indicate sealing,caulking and gasketing spec yes 1314.4 Recessed Lighting Fixtur Indicate IC rating,ASTM E283 certification,and gasketing or caulking to ceiling spec PRESCRIPTIVE/COMPONENT PERFORMANCE (Sections 1320-23 or 1330-34) yes Envelope Sum.Form Completed and attached. r,tch Provide component pertormance worksheet if necessary If"no"is shown for any question,provide explanation: _.�/ _` �. �