Laserfiche WebLink
s <br /> Mechanical PermitPlansPage of <br /> 2012 Washington State Energy Code Compliance Forms for Commercial,Group Rt,and>3 story R2 and R3 Revised.lune 2013 <br /> Project Address 3501 Colby Ave#103 Date 6/8/2016 <br /> The following information is necessary to check a mechanical permit application for commercial provision compliance with the 2012 <br /> WSEC. NOTE:Define print area in Excel prior to printin MECH-CHK pages. <br /> Applicability Location on Building Department <br /> (yes,no,na) Code Section Code Provision Information Required Plans Notes <br /> GENERAL PROVISIONS <br /> Equipment Sizing&Performance <br /> N/A C403.2.1 Load calculations Load calculations performed per ASHRAE Std 183 or equivalent per <br /> Chapter <br /> N/A C403.2.2 Equipment and system Output capacity of heating and cooling equipment and systems do not <br /> sizing exceed calculated loads note exceptions taken <br /> Yes C403.2.5 Minimum ventilation Ventilation(natural or mechanical)provided per IMC;indicate mechanical M 1 <br /> ventilation is capable of beingreduced to minimum re uirement per IMC <br /> C403.2.3& Equipment minimum Provide equipment schedules or complete MECH-SUM tables with type, <br /> C403.2.3.2& efficiency capacity,efficiency,test standard(or other efficiency source)for all <br /> Yes C403.2.12.1 mechanical equipment M 1 <br /> N/A C403.2.13 Electric motor efficiency Provide equipment schedule with hp,rpm,efficiency for all motors;note <br /> except. <br /> N/AC403.2.10 Fan power limitation Fan system motor hp or bhp does not exceed limits per Table <br /> / C403.2.10.1 1 <br /> A C403.2.10.3 Fractional hp fan motors Indicate fan motors 1/12 to 1 hp are ECM type or meet minimum efficiency <br /> N/A &C403.2.13 req. <br /> N/A C403.2.3 Maximum air cooled chiller Indicate air-cooled chiller capacity does not exceed air-cooled chiller limit <br /> capacity <br /> C403.2.1 Non-standard water-cooled Full-load and NPLV values for water-cooled centrifugal chiller adjusted for <br /> N/A chillers non-standard operational conditions <br /> C403.2.12.1. Centrifugal fan cooling Large capacity cooling towers with centrifugal fan(s)meet efficiency <br /> N/A towers requirements for axial fan open circuit cooling towers <br /> N/A C403.2.3 heaters Forced air furnace and unit Indicate intermittent ignition or IID,flue/draft damper&jacket loss <br /> C403.2.3.3 Packaged electric List equipment required to be heat pumps on schedule <br /> N/A heatin /coolin equipment <br /> N/A C403.2.3.4 Humidification Indicate method of humidification(note requirements for systems with <br /> economizer <br /> HVAC System Controls&Criteria <br /> Yes C403.2.4.1 Thermostatic controls Indicate locations of thermostatic control zones on plans,including M 1 <br /> perimeter systems <br /> Yes C403.2.4.1.1 Heat pump supplementary Indicate staged heating(compression/supplemental)&outdoor lock-out M 1 <br /> heat tem <br /> C403.2.4.2 Setpoint overlap(deadband) Indicate 5"F deadband minimum for systems controlling both heating& M 1 <br /> Yes cooling <br /> Yes C403.2.4.3 Automatic setback and Indicate zone t-stat controls with required automatic setback&manual M 1 <br /> shutdown override <br /> C403.2.4.3.3 Automatic(optimum)start Indicate system controls that adjust equip start time to match load M 1 <br /> Yes conditions <br /> C402.4.5.2& Indicate location of OSA,exhaust,relief and return air dampers;include <br /> Yes C403.2.4.4 Dampers AMCA rated leakage and control a motorized or ravi •note exceptions <br /> M 1 <br /> N/A C403.2.11 Heating outside a building Indicate radiant heat system and occupancy controls <br /> N/A C403.2.4.5 Snow melt systems Indicate shut-off controls based on outdoor conditions <br /> N/A C403.2.4.6 Combustion heating Indicate modulating or staged control <br /> equipment <br /> N/A C403.2.4.7 Group Ri hotel/motel Indicate method for guest room automatic setback&set-up of 5°F <br /> systems minimum <br /> N/A C403.2.4.8/9 Group R2/R3 dwelling unit Indicate 5-2 programmable thermostats in primary spaces with minimum of <br /> s stems two setbackperiods;note exceptions taken <br /> N/A C403.2.5.1 Demand controlled Indicate high-occupancy spaces and systems requiring DCV <br /> ventilation <br /> N/A C403.2.5.2 Occupancy sensors Indicate spaces requiring occupancy-based system control and method;or <br /> alternate means provided to automatically reduce OSA when partially <br /> Enclosed loading Indicate enclosed loading dock and enclosed parking garage ventilation <br /> N/A C403.2.5.3 dock/parking garage system activation and control method <br /> ventilation <br /> N/A C403.2.5.4.1 Kitchen exhaust hoods Indicate kitchen hoods requiring make-up air;indicate make-up air source <br /> and conditioning method <br /> Indicate lab exhaust systems requiring heat recovery,method&efficiency; <br /> N/A C403.2.5.4.2 Laboratory exhaust systems or alternative method taken(VAV,semi-conditioned makeup,or CERM <br /> calculation <br /> C403.2.6.1 Energy recovery- Indicate ventilation systems requiring ER,method&efficiency;note <br /> N/A ventilation systems exceptions <br /> N/A C403.2.6.2 Energy recovery-condensate s stems Indicate on-site steam heating systems requiring energy recovery <br /> N/A C403.2.6.3 Energy recovery- Indicate remote refrig.condensers requiring ER and use of captured energy <br /> condensers stems <br />