1701 PUGET DR 2017-08-11 - Laserfiche WebLink

Smart Energy Today Inc." PHOTOVOLTAIC SYSTEM AC DISCONNECSOLAR ELECTRIC SHOCK HAZARD OPERATINGRATED AC CURRENT CAUTION • •' • AIVOLTS IF A GROUND FAULT IS INDICATED AC NORMALLY GROUNDED CONDUCTORS 1001 Cooper Point Rd SW. MAY BE UNGROUNDED AND ENERGIZED LABEL LOCATION: POWER TO THIS BUILDING IS ALSO SUPPLIED FROM THE Suite 140-290 AC DISCONNECT,POINT OF INTERCONNECTION FOLLOWING SOURCES WITH DISCONNECTS LOCATED AS SHOWN Olympia,WA 98502 LABEL LOCATION: (PER CODE:CEC690.54) AT:® MAIN SERVICE PANEL&UTILITY METER Phone:888-405-8689 DC DISCONNECT,INVERTER PRODUCTION METER Fa 855-350-9430 (PER CODE:CEC 690.35(F)) WARNING •R be used when inverter is ungrounded) FUSED AC DISCONNECT support@smartenergyloday.net INVERTER • • • • NOT SOLAR LOAD CENTER REVISIONS RELOCATE OVERCURRENT DEVICE DESCRIPTION DATE REV LABEL LOCATION: INITIAL -21-2011 W ELECTRIC SHOCK HAZARD POINT OF INTERCONNECTION THE DC CONDUCTORS OF THIS (PER CODE:CEC 705.12(D)(7)) PHOTOVOLTAIC SYSTEM ARE UNGROUNDED [Not required if panelboard is rated not less than sum of ampere ratings AND MAY BE ENERGIZED of all overcument devices supplying it] Signature with Seal LABEL LOCATION. 10gg 1s .y p DC DISCONNECT,INVERTER 1 8 d (PER CODE:CEC 690.35(F)) ]To be used when inverter is ungrounded] LABEL LOCATION: MARKINGS PLACED ON ALL INTERIOR AND EXTERIOR DC CONDUIT,RACEWAYS,ENCLOSURES, AND CABLE ASSEMBLIES AT LEAST EVERY 10 FT,AT TURNS AND ABOVE/BELOW PENETRATIONS 71 4 6 AND ALL COMBINER/JUCTION BOXES.(PER CODE:IFC605.11.1.4) ELECTRIC SHOCK HAZARD DO NOT TOUCH TERMINALS SOLAR . • PROJECT NAME&ADDRESS TERMINALS ON BOTH LINE AND LOAD SIDES MAY BE ENERGIZED IN THE OPEN POSITION LABEL LOCATION: DISCONNECT,POINT OF INTERCONNECTION DC VOLTAGE IS ALWAYS PRESENT (PER CODE CEC690.13(B)) WHEN SOLAR MODULES ARE 17 ��`v--� • sf-1 '.-" r u«f-" (E)MAIN SERVICE PANEL (N)PV SOLAR COMBINER j E EXPOSED TO SUNLIGHT (INSIDE) -i O e r � (N)PV PRODUCTION METER 7 U L LABEL LOCATION: • (N)FUSED AC DISCONNECT 10N AC LABEL LOCATION: (PER CODE:CEC,POINT OF INTERCONNECTION POINT OF INTERCONNECTION E UTILITY METER U)N fl. (PER CODE:CEC 690.17(E)) ( ) (PER CODE:CEC 705.12(D)(4)) 9 - a ,I a-, SCO @ r N 00 Lo ELECTRIC SHOCK HAZARDW M n c DO NOT TOUCH TERMINALS LABEL LOCATION: ELECTRICAL NOTES Q Q N m TERMINALS ON BOTH LINE AND WEATHER RESISTANT MATERIAL,DURABLE ADHESIVE, v w UL969 AS STANDARD TO WEATHER RATING(UL LISTING 1. ALL EQUIPMENT TO BE LISTED BY UL OR OTHER NRTL,AND D_ LOAD SIDES MAY BE ENERGIZED ) OF MARKINGS NOT REQUIRED),MIN%¢"LETTER HEIGHT IN THE OPEN POSITION LABELED FOR ITS APPLICATION. � �W ARIAL OR SIMILAR FONT NON-BOLD,PLACED WITHIN �p f0 LABEL LOCATION: THE MAIN SERVICE DISCONNECT,PLACED ON THE 2.) ALL CONDUCTORS SHALL BE COPPER,RATED FOR 600 V ti W Z E AC DISCONNECT,POINT OF INTERCONNECTION OUTSIDE OF THE COVER WHEN DISCONNECT IS —AND 90 DEGREE C WET ENVIRONMENT. M O LU x PER CODE:CEC 690.17(E),CB OPERABLE WITH SERVICE PANEL CLOSED. 3.) WIRING,CONDUIT,AND RACEWAYS MOUNTED ON ROOFTOPS W >it J (PER CODE:CEC690,15,690.13(8)) SHALL BE ROUTED DIRECTLY TO,AND LOCATED AS CLOSE AS W W Q t POSSIBLE TO THE NEAREST RIDGE,HIP,OR VALLEY. _I W •• • ARRAY 4.) WORKING CLEARANCES AROUND ALL NEW AND EXISTING J LABEL LOCATION:• ,•• DISCONNECT SWITCH 5.) DRAWINGS INDICA E THE GENERA ARRANGEME T OF ELECTRICAL EQUIPMENT SHALL COMPLY WITH NEC26 O INVERTER,JUNCTION BOXES(ROOF),AC DISCONNECT LABEL LOCATION: SYSTEMS.CONTRACTOR SHALL FURNISH ALL NECESSARY U (PER CODE:CEC690.13.G.3&CEC 690.13.G.4) AT ALL AC DISCONNECTS (PER CODE:DEC 690.14(C)(1)) WARNING: OUTLETS,SUPPORTS,FITTINGS AND ACCESSORIES TO FULFILL PHOTOVOLTAIC APPLICABLE CODES AND STANDARDS. •• - • - 6.) WHERE SIZES OF JUNCTION BOXES,RACEWAYS,AND CONDUITS SHEET NAME LABEL LOCATION: "PT, STST-EiTi EQ11PPED 711TA RAPID ARE NOT SPECIFIED,THE CONTRACTOR SHALL SIZE THEM PLACARDS CONDUIT,COMBINER BOXSHUTDOWN" ACCORDINGLY. (PER CODE:CEC690.31(Gx3N4)&CEC 690.13(G)(4) 7.) ALL WIRE TERMINATIONS SHALL BE APPROPRIATELY 2016 NEC 690.56(0) LABELED AND READILY VISIBLE. SHEET sIZE ADHESIVE FASTENED SIGNS: 8.) MODULE GROUNDING CLIPS TO BE INSTALLED BETWEEN •THE LABEL SHALL BE SUITABLE FOR THE ENVIRONMENT MODULE FRAME AND MODULE SUPPORT RAIL,PER THE ANSI B WHERE IT IS INSTALLED. .WHERE REQUIRED ELSEWHERE IN THIS CODE,ALL FIELD GROUNDING CLIP MANUFACTURER'S INSTRUCTION. 11 11 X 17� APPLIED LABELS,WARNINGS,AND MARKINGS SHOULD 9.) MODULE SUPPORT RAIL TO BE BONDED TO CONTINUOUS _--- COMPLY WITH ANSI Z535A(NEC 110.21(B)FIELD MARKING). $HEFT NUMBER •ADHESIVE FASTENED SIGNS MAYBE ACCEPTABLE IF COPPER G.E.C.VIA WEEB LUG OR ILSCO GBL-4DBT LAY-IN LUG. PROPERLY ADHEREO.VINYL SIGNS SHALL BE WEATHER 10.) THE POLARITY OF THE GROUNDED CONDUCTORS IS NEGATIVE RESISTANT IIFC 605.11.1.31 P V-5