Laserfiche WebLink
Component • • • Js 4c/5b <br /> 2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2&R3 over 3 stories and all R1 Revised Oct 2013 <br /> Project Address Underwood Gartland 62 Date 06/21/2016 <br /> Occupancy Group * Commercial O Group R For Building Department Use <br /> Change in occupancy or space conditioning O <br /> Note-Proposed UA may exceed Target UA by 10%per C101.4.4 and C101.4.5 <br /> Fenestration Area as%gross above-grade wall area 6.8% Max.Target: 30.0% <br /> Skylight Area as%gross roof area 1.3% Max.Target: 5.0% <br /> Vertical Fenestration Alternates: None Selected on ENV-SUM <br /> Notes: 1:If vertical fenestration or skylight area exceeds maximum allowed per C402.3.1, then Target Area Adjustment of all applicable envelope <br /> elements will be calculated by the compliance form. Refer to Target Area Adjustments worksheet for this calculation. <br /> 2:U-factors shall come from Appendix A, Chapter C303, or calculated per approved method as specified in C402.1.2. <br /> Building Component Proposed UA Target UA <br /> Provide source of U-factor, page/plan#of assembly detail& ID U-factor x Area(A) =UA(U x A U-factor x Area(A)= UA(U x A) <br /> Y R=20.8331D:Rigid Above Deck 0.048 197766 9492.8 0.034 197766 6724.0 <br /> o R= ID:(R-20 Insultaion Only Per Table 102.2.6) Above Deck Insulation U-0.034 <br /> R= ID: <br /> N -0 R= ID: 0.031 <br /> m R= ID: Metal Building U-0.031 <br /> R= ID: <br /> R= ID: 0.021 <br /> R= ID: Single raft, attic,other U-0.021 <br /> O R= ID: <br /> R= ID: 0.055 <br /> R= ID: Steel/metal frame U-0.055 <br /> m <br /> R= ID: <br /> 'o a R= ID: 0.052 <br /> Q C0 R= ID: Metal Building U-0.052 <br /> N Y! R= ID: <br /> R= ID: 0.054 <br /> o R= ID: Wood Frame,other U-0.054 <br /> Cr <br /> a �: R= ID: <br /> O <br /> R=11 ID:w/Stick-pin Insulation R-11 (A103.3.7.1(2)) 0.081 67219 5444.7 0.104 67219 6990.8 <br /> N <br /> m R= ID: Mass Wall U-0.104 <br /> :E R= ID: <br /> R= ID: 0.104 <br /> m <br /> o�: R= ID: Assumed to be Mass Wall U-0.104 <br /> on � R= ID: <br /> (D R= ID: <br /> N R= ID: 0.031 <br /> m R= ID: Mass Floor U-0.031 <br /> o R= ID: <br /> R= ID: 0.029 <br /> E R= ID: Joist/Framing U-0.029 <br /> T <br /> LL R= ID: <br /> F-factor x Perimeter =UA(U x A) F-factor x Perimeter= UA(U x A) <br /> R= ID:No Insulation 0.730 2572 1877.6 0.540 2572 1388.9 <br /> CU <br /> R= ID: Slab-On-Grade U-0.54 <br /> : R= ID: <br /> R= ID: 0.550 <br /> R= ID: Heated Slab-On-Grade U-0.55 <br /> = R= ID: <br /> *Proposed non-residential CMU walls meeting Table C402.1.2 Area UA Area UA <br /> Footnote D requirements can use the target U-value of 0.104 rather Page 1 <br /> than Appendix A values. Show footnote requirements in plans. Subtotal F <br /> 267557 16815 L!I557 1 15104 <br /> Component Performance Compliance (UA) UA COMPLIES <br />