6201 ASSOCIATED BLVD JDS INC 2018-03-29

Frelf MJ Me 2015 Washington State Energy Code Compli rms for Commercial Buildings inclPing2,R3,R4 over 3 storieE Revised August 2016 Project Title: JDSTI Date 1/20/2017 Calculation d 0 Addition- , Addition For Building Department Use Area NOTE8 stand alone +existing al Spaces where<50%of b Spaces where>_50%of luminaires are replaced luminaires are replaced LPA 40 Standard a Additional Efficiency Package Option G Calculation 0406-3 Reduced Interior Lighting Power To comply with C406 3.the Proposed L PD shall be 25%lower than the Target LPA Type Refer to C406 3 for additional requirements Maximum Allowed Lighting Wattage NOTE 1 Location(plan#, Gross Interior Allowed Watts Allowed Building Area room#,or ALL) Area Description Area in f:2 Watts per f:2 (watts/f:2 x area) Office A2.1 Office Areas 2 714 0.66 17 92 Office A2.1 Restrooms 244 0.66 162 Manufacturing A21 Shop Area 5500 0.89 4895 facility Warehouse A2.1 open area 16542 0.40 6617 Total 25000 Proposed Lighting Wattage Location(plan#, Number of Wafts per Building Area room#) Fixture Description NOTE2,3,4,5 Fixtures Fixture NOTE6 Watts Proposed Office A2.1 2x4 Fluorescent 31 42 1302 Office A2.1 Downlights 12 9 108 Manufacturing A2.1 High Bay Lights 3 142 426 facility Warehouse A2.1 Strip Lights 4 41 164 Warehouse A2.1 High Bay Lights 8 142 1136 Compliance by Building Area NOTE' Total Allowed Total Proposed Interior Lighting Building Area Warnings Watts Watts Power Allowance Office 1954 1410 COMPLIES Manufacturing Confirm all fixtures are reported under proposed lighting-low watts 4895 426 COMPLIES facility relative to maximum allowed. Confirm all fixtures are reported under proposed lighting-low watts Warehouse 6617 1300 COMPLIES relative to maximum allowed. Note 1-List all unique building areas per Table C405.4.2(1)that occur in the Totalsl 134661:3136 project scope.Select building area category from drop down menu. Note 2-Proposed fixtures must be listed in the building area in which they occur.List all proposed lighting fixtures including exempt lighting equipment and existing-to-remain fixtures. Note 3-For proposed Fixture Description,indicate fixture type,lamp type(e.g.T-8),number of lamps in the fixture,and ballast type(if included). For track lighting,list the length of the track(in feet)in addition to the fixture,lamp,and ballast information. Note 4-Forlighting equipment eligible forexemption per C405.4.1,note exception numberand leave Watts/Fixture blank. Note 5-Existing-to-remain fixtures shall be included in the Proposed Lighting Wattage table in the same manner as new fixtures.Identify as existing in fixture description. Note 6-For proposed WattsrFixture enter the luminaire wattage for installed lamp and ballast using manufacturer or other approved source.For luminaires with screw-in lamps,enter the manufacturer's listed maximum input wattage ofthe fixture(not the lamp wattage).For low voltage lighting,enter the wattage ofthe transformer.For line voltage track/busway systems,enter the larger ofthe attached luminaire wattage or 50 watts/lineal foot,or enter the wattage limit of permanent current limiting device. Note 7-Proposed Wattage for each Building Area type shall not exceed the Allowed Wattage for that Building Area type.Trading wattage between Building Area types is not allowed under the Building Area Method compliance path. Note 8-Calculation Area Details.- a. etails:a.Lighting fixtures in a building addition may comply as a stand alone project,or they may be combined with the overall existing building lighting systems to demonstrate compliance.Refer to C502.1. b.For alterations and building additions,provide Building Area types and gross interior areas in the Maximum Allowed Lighting Wattage table.If a building addition will comply as combined with the overall existing builidng lighting systems, include all applicable existing Building Area types and gross interior areas. c.If less than 50%of existing lighting fixtures will be replaced,Ti CE form to document compliance. �