3407 WAVE DR 2017-09-25 - Laserfiche WebLink

Solid Sawn Joist Hangers • • Adjustable rr "rlelSkeivable U Hangers I Imt e J 6 This product Is preferable to similar connectors because of a)easier installation,b)higher loads,c)lower Installed cost, Range u+ or a combination of these features. „A„Flange r 'J The LSU and LSSU series of hangers may be sloped and skewed I( I m111 in the field,offering a versatile solution for attaching joists and rafters.These hangers may be sloped up or down and skewed left or right,up to 45°. " MATERIAL: See table o, FINISH:Galvanized.Some products available in ZMAX®coating; G® see Corrosion Information,pages 13-15. INSTALLATION: •Use all specified fasteners.See General Notes. \� •Attach the sloped joist at both ends so that the horizontal force developed by the slope is fully supported by the supporting members. ly up slopeOrd 0 •To see an installation video on this product,visit www.strotigtie.com. LSU26 t04e^"'n c CODES:See page 12 for Code Reference Key Chart. A �w� rA� o LSU and LSSU INSTALLATION SEQUENCE 9 0 •'® (for Skewed or Sloped/Skewed Applications) ® '' 0 ® d _ "A"Flanges U "A"Flanges Acute R, Side 1 Nails/ 0-45 STEP 1TS EP 2 STEP 3 Nail hanger to slope-cut Skew flange from 0-45°. Attach hanger to Slope to carried member,installing Bend other flange back the carrying member, 45°up or down Slope to seat nail first.No bevel along centerline of slots acute angle side first !q: 45°up or down necessary for skewed until it meets the header. (see footnote 4).Install V LSSU410 installation.Install joist Bend one time only. nails at an angle. (LSSU210-2 similar) LSSU28 nails at 45°angle. . These products are available with additional corrosion protection.Additional products on this page may also be available with this option,check with Simpson Strong-Tie for details. Dimensions Fasteners OF/SP Allowable Loads SPF/HF Allowable Loads Joist Model Ga 2 2 Code o Width No. W H A Face Joist Uplift Floor Snow Roof Uplift Floor Snow Roof Ref. Z (160) (100) (115) (125) (160) (100) (115) (125) Sloped Only Hangers 1'/2 LSU26 18 1% 42/e 1'h 6-10d 5-10dx1'h 535 695 810 865 415 600 695 745 z 11/2 LSSU28 18 1B/,s 7'/e 1'h 10-10d 5-10dx1'/z 535 1110 1275 1390 415 960 1105 1200 18,F7,L15 o � 11/2 LSSU210 18 19/16 81h is/e 10-10d 7-10dx1'h 875 1110 1275 1390 625 960 1105 1200 w 2'h LSSUH310 16 26/16 81h 3'/e 18-16d 12-10dx1'/2 1150 2295 2295 2295 990 1930 1930 1930 170 3 LSSU210-2 16 3'/e 8'/2 27/e 18-16d 12-10dx11/2 1150 2430 2795 3035 990 2160 2485 2700 18 F7,L15 3'h LSSU410 16 39/16 81h 25/e 18-16d 1210dx1'h 1150 2430 2795 3035 990 2160 2485 2700 Z Skewed Hangers or Sloped and Skewed 1'h LSU26 18 i9/e 4% 1Yz 6-10d 5-10dxl'h 535 695 810 865 415 600 695 745 g 11h LSSU28 18 1M 7'/s 11h 9-1Od 5-10dx11h 450 885 885 885 415 765 765 765 18,FT L15 11h LSSU210 18 19/16 8'h 1% 9-10d 7-10dxl1/2 785 995 1145 1205 625 860 995 1050 ® 2'h LSSU H310 16 29/16 8'h 3'/e 14-16d 12-10dx11h 1150 1600 1600 1600 990 1385 1385 1385 170 3 LSSU210-2 16 3% 81/2 27/a 14-16d 12-10dx11/2 1150 1625 1625 1625 990 1365 1365 1365CV 18 F7 L15 e? 3'h LSSU410 16 31/1s 81h 2% 14-16d 12-10dxl1h 1 1150 1625 1625 1625 990 1365 1365 1365 1.Roof loads are 125 °of floor loads unless limited by other criteria. 2.Uplift loads include an Increase for wind or earthquake loading with no further increase allowed; reduce when other loads govern. 3.Truss chord cross-grain tension may limit allowable loads in accordance with ANSI/TPI 1-2007. Simpson Strong-Tie®Connector SelectorT61 Software includes the evaluation of cross-grain tension in its hanger allowable loads.For additional information,contact Simpson Strong-Tie. 4.For skewed LSSU hangers,the Inner most face fasteners on the acute angle side are not installed. 5.Do not substitute 10dxl1/2"nails for face nails on slope and skew combinations or skewed only LSU and LSSU. 6.NAILS:16d=0.162"dia.x 31/2"long,10d=0.148"dia.x 3"long,10dxl1/2=0.148"dia.x 11/2"long. See pages 22-23 for other nail sizes and information,