13110 19TH AVE SE 2017-09-25 - Laserfiche WebLink

2012 Washington Stawrgy Code Compliance Forms for Commercial,Group R1W>3 story R2 and R3 PermitMechanical Plans ■ • 2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2&R3 over 3 stories and all R1 Revised Aug 2015 Project Address 2205 BROADWAY Date 5/13/2016 The following information is necessary to check a permit application for compliance with the mechanicial systems and equipment requirements of the Washington State Energy Code,Commercial Provisions. Applicable Code Section Code Provision Information Required-Must be in permit documents Location t Building Department (yes,no,n3) Documents Notes GENERAL PROVISIONS,CONTINUED HVAC System Controls&Criteria,Continued Enclosed loading Indicate enclosed loadingdock and enclosed parking na C403.2.5.3 dock/parking garage P g garage ventilation system activation and control method ventilation na C403.2.5.4.1 Kitchen exhaust hoods Indicate kitchen hoods requiring make-up air,indicate make-up air source and conditioning method na C403.2.5.4.2 Laboratory exhaust systems Indicate lab exhaust systems requiring heat recovery,method&efficiency,or alternative method taken(VAV,semi-conditioned makeup,or CERM calculation) na C403.2.6.1 Energy recovery(ER)- Indicate ventilations stems requiring ER,method&efficiency: ventilation systems y q 9 cy;note exceptions na C403.2.6.2 Energy recovery(ER)- Indicate on-site steam heating systems requiring energy recovery condensate systems na C403.2.6.3 Energy recovery(ER)- Indicate remote refrig.condensers requiring ER and use of captured energy cooler/freezer condensers na C403.4.6 Energy recovery(ER)- Indicate condenser systems requiring ER to pre-heat service water,indicate ER effectiveness, condenser systems note exceptions taken na C403.2.12 Variable flow control- Indicate fan and pump motors>_7.5 hp and the method of variable flow control(VSD or fans/pumps equivalent controls) na C403.2.12.1 Variable flow control-heat Indicate heat rejection equipment and cooling tower fans requiring variable flow control and rejection equipment method Indicate single zone fan systems requiring airflow reduction capability in response to reduced na C403.2.12.2 Large volume fan systems cooling or heating demand in a zone,or adjacent zones without separating walls,with>10,000 CFM supply air;note exceptions taken na C403.2.12.2 Single zone AC systems Indicate method of cooling demand-based fan control for air conditioning systems>110,000 Btu/h serving single zones na C403.2.4.10DDC system capabilities Identify all DDC system input/output control points and indicate capability for trending and demand res onse setpoint adjustment Ducting Systems yes C403.2.7.1& Duct construction Indicate all ductwork constructed and sealed per IMC,C402.4 leakage requirements and IBC SPEC C403.2.7.3 vapor retarder requirements 200700 M-111& yes 403.2.7.3.1- Duct pressure classifications Identify location of low,medium and high pressure ductwork on plans SPEC 233000 na C403.2.7.3.3 High pressure duct leakage Indicate high pressure duct leakage testing requirements on plans;provide test results to test jurisdiction when completed yes C403.2.7.1/IDuct insulation Indicate R-value of insulation on ductwork 200700 Piping Systems yes C403.2.8 Piping insulation Indicate R-value of insulation on piping SPEC 200700 yes C403.2.8.1 Piping insulation exposed to Indicate method of protection from damage/degredation SPEC weather 200700 SIMPLE SYSTEMS Qualifying Systems Qualifying single zone Verify unitary or packaged equipment does not exceed capacity limits,does not have active M-111& yes C403.3 MECH- systems humidifcation or simultaneous heating/cooling EQUIP na C403.3 Qualifying 2-pipe heating Verify 2-pipe heating-only system does not exceed capacity limits systems na C403.3.2 Hydronic system controls Refer to Complex Systems Section C403.4.3 Simple System Economizers na C403.3.1 Air economizer required Indicate cooling systems requiring economizer controls;note in equipment schedule i