13110 19TH AVE SE 2017-09-25 - Laserfiche WebLink

2012 Washington Staorgy Code Compliance Forms for Commercial,Group R1.>3 story R2 and R3 PermitMechanical Plans Page 3 , 2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2&R3 over 3 stories and all R1 Revised Aug 2015 Project Address 2205 BROADWAY Date 5/13/2016 The following information is necessary to check a permit application for compliance with the mechanicial systems and equipment requirements of the Washington State Energy Code,Commercial Provisions, Applicable Cade Section Code Provision Information Required-Must be in permit documents Location in Building Department (yes,no,na) Documents Notes COMPLEX SYSTEMS Complex System Economizers na C403.4.1 Air economizer required Indicate cooling systems requiring economizer controls;note in equipment schedule na C403.4.1 Air economizer exceptions Indicate eligible exception(s)taken and provisions to comply with exception(s) na C403.4.1.1 Water economizer capacity For eligible systems where water economizer may be provided in lieu of air economizer, indicate system is capable of 100%cooling capacity at 50°F db/45°F wb OSA na C403.4.1.2 Water economizer Indicate precooling coils and heat exchangers in water economizer system do not exceed maximum pressure drop pressure drop limit na C403.4.1.3 Integrated economizer Indicate capability for partial economizer operation for air or water economizer systems operation na C403.4.1.4 Economizer heating system Verify control method of HVAC systems with economizers does not increase building heating impact energy usage during normal operation Specific System Requirements na C403.4.2& VAV fan control Indicate fans requiring variable flow control and method C403.2.12 na C403.4.2.1 VAV fan static pressure Indicate sensor locations on plans;include at least one sensor per major duct branch sensors na C403.4.2.2 VAV fan static pressure Indicate fan system static pressure setpoint based on zone requiring most pressure setpoint na C403.4.5 VAV systems serving Indicate supply air systems serving multiple zones,method of primary air control,and zones multiple zones served,Indicate VAV or note exceptions taken na C403.4.5 VAV systems serving For each air system terminal,indicate the maximum air flow rate of primary supply air during multiple zones zone peak cooling and the maximum airflow rates during zone peak heating. na C403.4.5.4 VAV system supply air reset Indicate controls that automatically reset supply air temp in response to loads na C403.4 Large capacity cooling Indicate method of multi-stage or variable control for building cooling system capacity>300 systems tons na C403.4.7 Hot gas bypass limitation Indicate cooling equipment unloading or capacity modulation method na C403.4.3 Large capacity boiler Indicate multi-stage or modulating burner for single boilers>500,000 Btu/h systems na C403.4.3 Boiler sequencing Indicate automatic controls that sequence operation of multiple boilers na C403.4.3.5 Chiller/boiler plant pump Indicate capability to automatically reduce overall plant flow and shut-off flow through chillers& isolation boilers when not in use na C403.4.3.6& Variable flow control- Indicate pumps requiring variable flow control&method C403.2.12 pumps na C403.2.12.1 Variable flow control- Indicate cooling tower fans requiring variable flow control and method &C403.4.4 cooling towers na C403.4.3.4 Hydronic system part load Indicate heating&chilled water systems have the capability to automatically reset supply water controls temp AND reduce flow by>_50%for systems>300,000 Btu/h na C403.4.3.2 Two-pipe changeover Indicate deadband,heating/cooling mode scheduling and changeover temperature range systems na C403.4.3.3.1 Water loop heat pump- Indicate capability of central equipment to provide min.20°F water supply temp deadband deadband between heat rejection and heat addition modes na C403.4.3.3.2.1Water loop heat pump- Indicate method used to limit system heat loss when heat rejections is not needed heat rejection,Zone 4 na C403.4.3.3.2.2 Water loop heat pump- Provide heat exchanger that separates cooling tower and heat pump loop heat rejection,Zone 5 na C403.4.3.3.3 Water loop heat pump- Indicate 2-way isolation valve on each heat pump and variable flow control for systems with isolation total pump power,10 hp na C403.5 Walk-in cooler/freezer- Indicate w/sf&control method for walk-in cooler/freezer door anti-sweat heaters anti-sweat heaters