1502 RUCKER AVE 2017-10-25 - Laserfiche WebLink

ICC A117.1-2009 Chapter 9. Built-in Furnishings and Equipment Chapter 9. Built-in Furnishings and Equipment 901 General 903 'Be"hes 901.1 Scope. Built-in furnishings and equipment 903.1 General. Accessible benches shall comply with required to be accessible by the scoping provisions Section 903. adopted by the administrative authority shall comp6903.2 Clear Floor Space. A clear floor space comply- with the applicable provisions of Chapter 9. ing with Section 305, positioned for parallel approach to I 902 Dining Surfaces and Work Surfaces the bench seat, shall be provided. 903.3 Size. Benches shall have seats 42 inches (1065 902.1 General. Accessible dining surfaces and wo k mm) minimum in length, and 20 inches (510 mm) mini- surfaces shall comply with Section 902. mum and 24 inches (610 mm) maximum in depth. EXCEPTION: Dining_surfaces and work surfaces pri- 903.4 Back Support. The bench shall provide for back a,.mari for chirdren's use stall e�itted�fo'coI support or shall be affixed to a wall. Back support with Section 902.5. - pp pport shall be 42 inches (1065 mm) minimum in length and shall 902.2 Clear Floor Space. A clear floor space comply- extend from a point 2 inches (51 mm) maximum above ing with Section 305, positioned for a forward approach, the seat surface to a point 18 inches (455 mm) mini- shall be provided. Knee and toe clearance complying mum above the seat surface. Back support shall be 21/2 with Section 306 shall be provided. inches (64 mm) maximum from the rear edge of the EXCEPTIONS: seat measured horizontally. _f 1. At drink surfaces 12 inches(305 mm) or less in e top of the bench seat shall be 17 !G depth, knee and toe space shall not be inches (430 mm) minimum and 19 inches (485 mm) required to extend beneath the surface beyond maximum above the floor, measured to the top of the the depth of the drink surface provided. seat. 2. Dining surfaces that are 15 inches (380 mm) EXCEPTION: Benches primarily for children's use minimum and 24 inches (610 mm) maximum in shall be permitted to be 11 inches (280 mm) mini- height are permitted to have a clear floor mum and 17 inches (430 mm) maximum above the space complying with Section 305 position floor, measured to the top of the seat. Nr a parallel approach. 903.6 Structural Strength.Allowable stresses shall not '902 xE pow-Surfaces. e a e no sharp or be exceeded for materials used where a vertical or hori- abrasive surfaces under the exposed portions of dining zontal force of 250 pounds (1112 N) is applied at any surfaces and work surfaces. point on the seat, fastener mounting device, or support- 902.4 Height.The tops of dining surfaces and work sur- ing structure. faces shall be 28 inches (710 mm) minimum and 34 903.7 Wet Locations. Where provided in wet locations inches (865 mm) maximum in height above the floor. the surface of the seat shall be-slipp resisTatit-arid shall not accumulate water--_---' 902.5 Dining Surfaces and Work Surfaces for Chil- dren's Use. Accessible dining surfaces and work sur- 904 Sal se nd Service Counters faces primarily for children's use shall comply with Section 902.5. 90 .1 General. Accessible sales and service counters d windows shall comply with Section 904 as applica- EXCEPTION: Dining surfaces and work surfaces le. used primarily by children ages 5 and younger shall not be required to comply with Section 902.5 where a EXCEPTION: Drive up only sales or service counters clear floor space complying with Section 305 is pro- and windows are not required to comply with Section vided and is positioned for a parallel approach. 904. 902.5.1 Clear Floor Space.A clear floor space com- 904.2 Approach.All portions of counters required to be plying with Section 305, positioned for forward accessible shall be located adjacent to a walking sur- approach, shall be provided. Knee and toe clearance face complying with Section 403. complying with Section 306 shall be provided. 904.3 Sales and Service Counters. Sales and service EXCEPTION: A knee clearance of 24 inches (6 counters shall comply with Section 904.3.1 or 904.3.2. mm) minimum above the floor shall be permitted. The accessible portion of the countertop shall extend 902.5.2 Height.The tops of tables and counters hall the same depth as the sales and service countertop. be 26 inches (660 mm) minimum and 30 inches (760 904.3.1 Parallel Approach. A portion of the counter mm) maximum above the floor. surface 36 inches (915 mm) minimum in length and 36 inches (915 mm) maximum in height above the -?1