6611 ASSOCIATED BLVD AMAZON 2021-02-17

: • • � ' � • • 2015 WSEC Compliance Forms for Commercial Buildings including R2,R3,&R4 over 3 stories and all R1 Revised Jun 2016 Project Title: Amazon Delivery Station DSE4 Date 05/11/2017 The following information is necessary to check a building permit application for compliance with the building envelope requirements in the Washington State Energy Code,Commercial Provisions. Applicability Code Location in Building (yes,no,na) Section Component Compliance information required in permit documents Documents Department Notes SCOPE Low energy spaces are identified on plans;include project information, C402.1.1 Low energy spaces and calculations if applicable,that demonstrate spaces are eligible for envelope provisions exemption Semi-heated spaces are identified on plans,include calculations that C402.1.1.1 Semi-heated spaces demonstrate spaces are eligible for wall insulation exemption Provide building area,average wall and roof U-factor,and installed C402.1.2 Equipment Buildings equipment information that demonstrates equipment building is eligible for envelope provision exemption Walk-in and Cooler and freezer spaces are identified on plans;C410 envelope C410.2 warehouse cooler compliance forms provided(pending) and freezer spaces C101.4.1 Mixed occupancy Spaces with different occupancy requirements are identified on plans Existing unconditioned spaces changing to semi-heated or conditioned C5032 Change of space space,and existing semi-heated spaces changing to conditioned space, conditioning are identified on plans.Include calculations that demonstrate baseline and final level of conditioning. Existing F,S and U-occupancy spaces undergoing a change in occupancy are indicated on plans;include calculations that demonstrate upgrade . complies with the current WSEC. Change of Pre-2002 Group R spaces undergoing a change to a commercial C505.1 occupancy are indicated on plans;include calculations that demonstrate occupancy upgrade complies with the current WSEC. Non-Group R occupancy spaces undergoing a change to Group R are indicated on plans:include calculations that demonstrate upgrade complies with the current WSEC. ENVELOPE PROVISIONS Indicate envelope insulation compliance path and provide applicable forms;ENV-PRESCRIPTIVE or ENV-UA/ENV-SHGC for component C103.2 Compliance Performance C103.6.3 documentation If complying via total buidling performance,provide a list of all proposed envelope component types,areas and U-values C303.1.1 Insulation Indicate identification mark shall be applied to all insulation materials and C303.1.2 identification insulation installed such that the mark is readily observable during inspection C303.1.3 Fenestration product Fenestration products shall be labeled with rated U-factor,SHGC,VT,and C402.4.3 rating leakage rating Indicate installation methods,thicknesses,densities and clearances to C303.1.1 General insulation achieve the intended R-value of all insulation materials: C402.2.1 installation Where two or more layers of rigid insulation will be used,indicate that edge joints between layers are staggered Indicate R-value(s)of cavity/continuous insulation on roof sections; Indicate framing materials on roof sections; Indicate method of framing for ceilings below vented attics and vaulted ceilings per A1022(std,adv); C103.2 Roof assembly Provide area weighted average U-factor calculation for insulation whose C402.22 insulation thickness varies by 1 inch or less; Indicate effective U-factors of tapered insulation entirely above deck per A102.2.6;include roof configuration and slope,maximum R-value at peak and minimum R-value at low point for all roof surfaces Indicate R-values for thermal spacers and each insulation layer,and liner system(LS)method for metal building roofs C402.2.2 Skylight curb Indicate curb insulation R-value on roof section if not included in skylight insulation NFRC rating Indicate R-value(s)of cavitylcontinuous insulation on wall sections; Indicate framing materials on wall sections; Indicate method of framing for wood const per A1032(std,int,adv); C103.2 Indicate material density category,wall weight and heat capacity for C402.2.3 Above/below grade qualifying mass walls; C4022.4 wall insulation C303.2.1 For qualifying ASTM C90 masonry walls,indicate loose-fill core insulation material and percentage of cores filled including grouted cores,bond beams,vertical fills,headers and any other grouted cores; Indicate method of protection of exposed exterior basemenUcrawlspace f� wall insulation , 'F�� t , �, .