10122 7TH AVE SE 2018-02-12 - Laserfiche WebLink

Job Truss Tree Qty Ply SE•TMENTS 110891382 68511099 A02 Common 28 1 Job Reference(optional) The Truss Co., Burlington,WA,98233 7.640 s Oct 7 2015 MiTek Industries,Inc.Wed Dec 02 14:40:59 2015 Page 1 ID:JRyKDtEV2yu?IHfinEZADYyKWtF-14fMnUn2RaXYSXwA4wCJYaYRJNO1vZ18eMUvavyCzkY 6-8-13 I 13-4-0 I 19-11-2 26-8-0 6-8-13 6-7-3 6-7-3 6-8-13 4x4= Scale=1:45.9 3 V. 6.00 t2 4x4 4x4 M 2 4 d /, 144N%so 1 5 i3x4 9 11 12 8 7 ►=� 3x4 10 6 3x4* 3x4= 3x4= 3x4= 3x4 26-8-0 1 1-4-0 14-2 9-2.4 17-5-12 I 2544 251.410 1-4.0 0--2 7-7-8 8-3-8 7-7-80-2-i2 1-4-0 Plate Offsets(X,Y)— [1:0-2-10,0-1-81,[5:0-2-10,0-1-81 LOADING (psf) SPACING- 2-0-0 CSI. DEFL. in (loc) 1/defl L/d PLATES GRIP TCLL 25.0 Plate Grip DOL 1.15 TC 0.54 Vert(LL) -0.23 7-9 >999 240 MT20 185/148 TCDL 8.0 Lumber DOL 1.15 BC 0.59 Vert(TL) -0.36 7-9 >778 180 BCLL 0.0 * Rep Stress Incr YES WB 0.93 Horz(TL) 0.05 6 n/a n/a BCDL 7.0 Code IRC2012/TP12007 (Matrix) Weight:111 lb FT=20% LUMBER- BRACING- TOP CHORD 2x4 HF No.2 TOP CHORD Structural wood sheathing directly applied or 4-3-1 oc purlins. BOT CHORD 2x4 HF No.2 BOT CHORD Rigid ceiling directly applied or 6-0-0 oc bracing. WEBS 2x4 DF Stud*Except* MiTek recommends that Stabilizers and required cross bracing W1:2x4 HF No.2 be installed during truss erection,in accordance with Stabilizer Installation guide. REACTIONS. (lb/size) 10=1067/0-5-8 (min.0-1-12),6=1067/0-5-8 (min.0-1-12) Max Horz 10=-81(LC 6) Max Uplift 10=-74(LC 8),6=-51(LC 8) FORCES. (Ib)-Max.Comp./Max.Ten.-All forces 250(Ib)or less except when shown. TOP CHORD 2-3=1244/111,3-4=-1244/113 BOT CHORD 9-10=-41/1169,9-11=0/826,11-12=0/826,8-12=0/826,7-8=0/826,6-7=-43/1169 WEBS 3-7=-11/413,4-7=-295/100,3-9=-8/413,2-9=-295/98,2-10=-1430/145,4-6=-1430/125 NOTES- 1)Unbalanced roof live loads have been considered for this design. 2)Wind:ASCE 7-10;Vult=110mph(3-second gust)V(IRC2012)=87mph;TCDL=4.2psf;BCDL=4.2psf;h=25ft;B=45tt;L=27ft;eave=off; Cat.II;Exp B;enclosed;MWFRS(directional);cantilever left and right exposed;end vertical left and right exposed;Lumber DOL=1.60 plate grip DOL=1.60 3)This truss has been designed for a 10.0 psf bottom chord live load nonconcurrent with any other live loads. 4)*This truss has been designed for a live load of 23.0psf on the bottom chord in all areas where a rectangle 3-6-0 tall by 2-0-0 wide will fit between the bottom chord and any other members,with BCDL=7.0psf. 5) Provide mechanical connection(by others)of truss to bearing plate capable of withstanding 100 lb uplift at joint(s)10,6. 6)This truss is designed in accordance with the 2012 International Residential Code sections R502.11.1 and R802.10.2 and referenced standard ANSI/TPI 1. 7)"Semi-rigid pitchbreaks with fixed heels"Member end fixity model was used in the analysis and design of this truss. i V. . Po 4, LOAD CASE(S) Standard ��\�, .;WAt•;,94 � '"--41.,(1;4i, Cir ;r O1 4>frt► °' of 19969 4'54 December 2,2015 . Immo A WARNING-Verify design parameters and READ NOTES ON THIS AND INCLUDED MITEK REFERENCE PAGE Ml1-7473 BEFORE USE. Design valid for use only with MiTek connectors.This design is based only upon parameters shown,and is for an individual building component. Applicability of design paramenters and proper incorporation of component is responsibility of building designer-not truss designer.Bracing shown is for lateral support of Individual web members only.Additional temporary bracing to insure stability during construction Is the responsibillity of the erector.Additional permanent bracing of the overall structure is the responsibility of the building designer.For general guidance regarding AeA fabrication,quality control,storage,delivery,erection and bracing,consult ANSIITPI1 Quality Criteria,DSB-89 and BCSI1 Building Component 1,. Safety Information available from Truss Plate Institute,583 D'Onofrio Drive,Madison,WI 53719. theTRUSSco.uC. / I