2707 COLBY AVE HDR 2018-05-01 - Laserfiche WebLink

" EXISTING SMOKE DETECTOR , ' , DN-6935:E•H-202 FSP-851 (A) Series N C�T 1 F 1 E R� Intelligent Plug-In Photoelectric Smoke Detectors with FlashScanO b�/ H On e�/We(� , :��:.��, �.. � General � � �� _ • Notifier FSP-851(A) Series intelligent piug-in smoke detec- �� y J tors with integral communication provide features that sur- pass conventional detectors. Detector sensitivity can be �, ,a programmed in the control panel software. Sensitivity is con- '{ " tinuously monitored and reported to the panel. Point ID capa- '�`` bility allows each detector's address to be set with rotary, decimal address switches, providing exact detector location °_� � s ,._ �, �o�. for selective maintenance when chamber contamination �� ¢: � ' ,�' , reaches an unacceptable level. The FSP-851(A) photoelec- �r` tric detector's unique optical sensing chamber is engineered - .: to sense smoke produced by a wide range of combustion sources. Dual electronic thermistors add 135°F(57°C)fixed- temperature thermal sensing on the FSP-851T(A).The FSP- 851 R(A) is a remote test capable detector for use with FSP-851(A) in B210LP(A)Base m DNR(A)/DNRW duct detector housings. FSP-851(A) series detectors are compatible with Notifier Onyx and CLIP series Fire Alarm Control Panels{FACPs). FlashScanC� (U.S. Patent 5,539,389) is a communication Specifications protocol developed by Notifier that greatly increases the Sensitivity:0.5%to 2.35%per foot obscuration speed of communication between analog intelligent devices. Size•2.1"(5.3 cm)high;base determines diameter. Intelligent devices communicate in a grouped fashion. If one ' of the devices in the group has new information, the panel's —B210�P(A):6.1"(15.5 cm)diameter. CPU staps the group poll and concentrates on single points. —B501(A):4.1"(10.4 cm)diameter. The net effect is response speed greater than five times that _B200S(A)•6.875"(17.46 cm)diameter. of earlier designs. —6200SR(A):6.875"(17.46 cm)diarr�ter. F@1t!!1'eS —B224R6(A):6.2"(15.748 cm)diameter. ' • Sleek,low-profile design. —B224BI(A):6.2"(15.748 cm)diameter. • Addressable-analog communication. Shipping Weight:5.2oz.(147g). • Stable communication technique with noise immunity. Operating Temperature range: FSP-851(A), 0°C to 49°C • Low standby current. (32°F to 120°F). FSP-851T(A),0°C to 38°C(32°F to 100°F). Low temperature signal for FSP-851T(A) at 45°F +/- 10°F • Two-wire SLC connection. (7.22°C +/- 5.54°C). FSP-851 R(A) installed in a DNR(A)/ • Compatible with FlashScanO and CLIP protocol systems. DNRW,-20°C to 70°C(-4°F to 158°F). • Rotary,decimal addressing(1-99 on CLIP systems, 1-159 UUULC Listed Velocity Range: 0-4000 ft/min. (1219.2 m/ on FlashScan systems). min.),suitable for installation in ducts. • Optional remote,single-gang LED accessory. Relative Humidity: 10%-93%noncondensing. • Dual LED design provides 360°viewing angle. Thermal Ratings:Fixed-temperature setpoint 135°F(57°C). • Visible bi-color LEDs blink green every time the detector is addressed, and illuminate steady red on alarm (FlashS- DETECTOR SPAC/NG AND APPLICATIONS can systems on/y). Notifier recommends spacing detectors in compliance with • Remote test feature from the panel. NFPA 72. In low airflow applications with smooth ceiling, • Walk test with address display (an address on 121 will space detectors 30 feet (9.144m) for ceiling heights 10 feet blink the detector LED: 12-[pause]-1(F/ashScan systems (3.148m) and higher. For specific information regarding only). detector spacing,placement,and special applications refer to Built-in functional test switch activated by external magnet. NFPA 72. System Smoke Detector Application Guide, docu- � ment A05-1003, is available at systemsensor.com • Built-in tamper-resistant feature. • Sealed against back pressure. ELECTR�cat SPeCiF�Canon►s • Constructed of off-white fire-resistant plastic, designed to Voltage Range: 15-32 volts DC peak. commercial standards, and offers an attractive appear- Standby Current(max.avg.): 300NA C�? 24VDC(one com- ance. munication every five seconds with LED enabled). ' • 94-5V plastic flammability rating. LED Current(max.):6.5mA @ 24 VDC("ON"). • SEMS screws for wiring of the separate base. • Optional relay,isolator,and sounder bases. DN-6935:E•2/11/2015—Page t of 2