1205 SE EVERETT MALL WAY CELL PHONE REPAIR 2018-05-23

ICC A117.1-2009 Chapter 9. Built-in Furnishings and Equipment �pter � uilt-in Furnishings and Eq i rr,ent 901 General 903 Benches 901.1 Scope. Built-in furnishings and equipment 903.1 General. Accessible benches shall comply with required to be accessible by the scoping provisions Section 903. adopted by the administrative authority shall compiy g03.2 Clear Floor Space. A clear floor space comply- with the applicable provisions of Chapter 9. ing with Section 305, positioned for parallel approach to ' 902 Dining �ur�aces and Work Surfaces the bench seat, shall be provided. 903.3 �ize. Benches shall have seats 42 inches (1065 902.1 General. Accessible dining surfaces and work mm) minimum in length, and 20 inches (510 mm) mini- surfaces shall comply with Section 902. mum and 24 inches (610 mm) maximum in depth. EXCEPYION: Dining surfaces and work surfaces pri- g03.4 Back Support. The bench shall provide for back marily for children's use shall be permitted to comply support or shall be affixed to a wall. Back support shall with Section 902.5. be 42 inches (1065 mm) minimum in length and shall 902.2 Clear Floor Space. A clear floor space comply- extend from a point 2 inches (51 mm) maximum above ing with Section 305, positioned for a forward approach, the seat surface to a point 18 inches (455 mm) mini- shall be provided. Knee and toe clearance complying mum above the seat surface. Back support shall be 2'/2 with Section 306 shall be provided. inches (64 mm) maximum from the rear edge of the EXCEP710NS: seat measured horizontally. 1. At drink surfaces 12 inches (305 mm)or less in 903.5 Height. The top of the bench seat shall be 17 depth, knee and toe space shall not be inches (430 mm) minimum and 19 inches (485 mm) required to extend beneath the surface beyond maximum above the floor, measured to the top of the the depth of the drink surface provided. seat. 2. Dining surfaces that are 15 inches (380 mm) EXCEPTION: Benches primarily for children's use minimum and 24 inches(610 mm) maximum in shall be permitted to be 11 inches (280 mm) mini- _ height are permitted to have a clear floor mum and 17 inches (430 mm) maximum above the space complying with Section 305 positioned floor, measured to the top of the seat. for a parallel approach. 903.6 Structural Strength.Allowable stresses shall not be exceeded for materials used where a vertical or hori- 902.3 Exposed Surfaces. There shall be no sharp or Zontal force of 250 pounds (1112 N) is applied at any abrasive surfaces under the exposed portions of dining point on the seat, fastener mounting device, or support- surfaces and work surfaces. ing structure. 902.4 Height.The tops of dining surfaces and work sur- g03.7 Wet Locations. Where provided in wet locations faces shall be 28 inches (710 mm) minimum and 34 the surface of the seat shall be slip resistant and shall inches (865 mm) maximum in height above the floor. not accumulate water. 902.5 Dining Surfaces and Work Surfaces for Chil- dren's Use. Accessible dining surfaces and work sur- 904 Sales and Service Counters faces primarily for children's use shall comply with g04.1 General. Accessible sales and service counters Section 902.5. and windows shall comply with Section 904 as applica- � EXCEPTIOIV: Dining surfaces and work surfaces ble. used primarily by children ages 5 and younger shall EXCEPTION: Drive up only sales or service counters not be required to comply with Section 902.5 where a and windows are not required to comply with Section clear floor space complying with Section 305 is pro- g04. vided and is positioned for a parallel approach. 902.5.1 Clear Floor Space. A clear floor space com- 904.2 Approach. All portions of counters required to be plying with Section 305, positioned for forward accessible shall be located adjacent to a walking sur- approach, shall be provided. Knee and toe clearance face complying with Section 403. complying with Section 306 shall be provided. 904.3 Sales and Service Counters. Sales and service EXCEf'TION: A knee clearance of 24 inches (610 counters shall comply with Section 904.3.1 or 904.3.2. mm) minimum above the floor shall be permitted. The accessible portion of the countertop shall extend the same depth as the sales and service countertop. 902.5.2 lieight.The tops of tables and counters shall 904.3.1 Parallel Approach. A portion of the counter be 26 inches (660 mm) minimum and 30 inches (760 surface 36 inches (915 mm) minimum in length and mm) maximum above the floor. 36 inches (915 mm) maximum in height above the -I ) � / si%'�