3402 MCDOUGALL AVE SNO CO PW 2018-11-14

� � � � � � � � ■ 2015 WSEC Compliance Forms for Commercial Buildings including R2, R3,&R4 over 3 stories and all R1 Revised Jun 2016 Project Title: Seaway Transit Center-Comfort Station Date 02/13/2017 Fenestration Area as%gross above-grade wall area 2•9� Max.Target: 30.0$ For Building Department Use Skylight Area a5%gross roof area Max.Target: 3.0$ If vertical fenestration or skylight area exceeds maximum allowed per C402.4.1,then the project must compl via Component Performance and provide ENV-UA and ENV-SHGC forms. Buildin COIll onent R-Value Method for U-Factor/F-Factor Method for g p Prescriptive Compliance Prescriptive Compliance Perim. Ins. Full Slab CI Provide plan/detail#of assembly and description R-Value R-Value F-Factor F-Factor Source'o � DETAIL 2/A2.5 � L 2"RIGID INSULATION 24"AT PERIMETER 10.0 I m � c o -o � � m m � = I ns. ssem y Provide ID from door schedule and description R-Value U-Factor U-Factor Source" N �' DOORS 001-004 o .a' SOLID CORE � o � , a� � i 6 L N N a � O Q Solar Heat Gain Coefficient(SHGC) U-Factor for Prescriptive Compliance ro�ec ion rien a ion Factor(PF) (N or Assembly Assembly Provide ID from wlndow schedule and description if applicable12 SEW)13 SHGC14 U-Factor U-Factor Source" @ 6 GLASS BLOCK FRAME UNITS-20"X20" SEW 0.40 � I � c ' Z I o � 4 DOOR TRANSOM UNITS-36"X18" N ! 0.40 ' � ,x w - N (6 C C� � G (0 Q U p r — � � N � � N I � y � L n � T I � Y — I (� Q I Note 1-Insulation that is continuous except for fasteners may be entered here if the cross-sectional area of ineta/penetration through otherwise continuous insulation is/ess than 0.12%. Note 2-Alternate prescriptive continuous insulafion R-values per Table C402.1.4,Footnote F inay be used if the cross sectional area of inetal penetrations exceeds 0.04%but is less than 0.12%. Calculations are required to use these alternate R-values. Note 3-Opaque assembly U-factors shall come from Appendix A or calculated per approved method as specified in C402.1.5.1. Specify the table number or calculation page number. Note 4-Thermal spacer blocking and liner system are required for prescriptive R-Value compliance in metal building roof assemblies. Nofe 5-Intermediate framing is required for prescriptive R-Value compliance in wood-framed wall assemblies. Note 6-Proposed CMU mass walls in non-Group R that meet Tab/e C402.1.4 Footnote D requirements can enter the target prescriptive U-va/ue of 0.104. Note 7-Mass transfer slab edges must be covered with an assemb/y having an overal U-factor of 0.2. Note 8-Refer to Table C402.1.3.Footnote E for prescriptive R-Value requirement for stee/floor joist assemblies. Note 9 -Prescriptive s/ab-on-grade insulation shall extend from top of slab to minimum length per an approved method as defined in C402.2.6. Nofe 10-Slab-on-grade F-Factors shall come from Appendix A or calculated per approved method as specified in C402.1.5.1. Note 11-Opaque door U-factors sha/l come from Appendix A or calculated per approved method as specified in C402.1.5.1.A door is defined as opaque if less than 50%of the door area has glazing. Note 12-Refer to Equation C4-6 Projection Factor Calculation. Note 13-N=Oriented within 45 degrees of true north, SEW=All other orientations. Note 14-Fenestration assembly U-Factor and SHGC shall be the manufacturer's NFRC product rating, which includes the glazing and frame, or shall be the default value per Section C303.1.3. Note 15-List all above-grade Group R mass walls and steel frame wal/s in Group R Walls section. List commercia/above grade walls and all other Group R above grade walls in Opaque Walls-Above Grade.