3402 MCDOUGALL AVE SNO CO PW 2018-11-14

• � • • ! � ' � • 2015 Washington State Energy Code Compliance Forms for Commercial Buildings including R2,R3,R4 over 3 srories and all R1 Revised August 2016 ProjectTitle: McDougall Date 2/26/2017 The foliowing information is necessary to check a permit application for compliance with the lighting,motor,and electrical requirements in the Washington State Energy Code,Commercial Provisions. Applicability Location in Building Department (yes,no,na) Code Section Component Compliance information required in permit documents Documents Notes LIGHTING CONTROLS Lighting controls, For all lighting fxtures,indicate lighting control method on plans Yes C4052 E2.0 general for spaces and lighting zone(s)served,or exception taken Luminaire level Indicate on plans all fixtures provided with LLLC in lieu of xA C4052 lighting controls C4052 lighting controls;provide description of control (LLLC) capabilities and pertormance parameters For permanently installed lighting fixtures in dwelling units, xA C405.1 Lighting in dwelling indicate lighting control method on plans for spaces and units lighting zone(s)served,or demonstrate compliance with high efficacy exception C405.2.3 C405.2.1.1 Indicate on plans the method of manual lighting control(whethe combined with occupancy sensor,automatic light reduction, Yes C40522.2 Manual controls E2.0 C4052.4 daylight responsive or specific application controls),location of C405.2.5 manual control device and area or specifice application it serve C4052.2.1 Manual interior Indicate on plans which method of manual 50%lighting load Yes C4052.2.2 reduction is provided,or whether lighting load is reduced via E2.0 C4052.3 lighting controls occupancy sensors or daylight responsive controls Indicate on plans the method of automatic shut-off control during unoccupied periods(occupancy sensor or time switch) E2.0 Yes C405.2.2 Method of automatic for all lighting zones; ------- -------- --------- ------ shut-off control Indicate locations where automatic shutoff is provided by other methods(occupancy sensor or digital timer switch)or which time switch control exception applies Indicate on plans the spaces served by occupancy sensors; E2.0 Yes C4052.1 Occupancy sensor Indicate whether occupancy sensor controls are configured to C4052.1.1 controls be manual-on,automatic 50°/o-on,or serve a space eligible for automatic 100%-on per exception Occupancy sensor Indicate aisleways and open areas in warehouse spaces NA C405.2.1.2 controls- provided with occupancy sensor controls that reduce lighting warehouses power by 50°/ NA C405.2.6 Digital timer switch Indicate required digital timer switch control function when control is used Yes C405.2.2.1 Automatic time Indicate locations of override switches on plans and the lighting E2_0 switch controls zone(s)served,include area sq.ft. Indicate primary and secondary sidelight daylight zone areas on plans,include sq.ft.; C405.2.4.2 Daylight zones- Indicate toplight daylight zone areas on plans,include sq.ft._ ---------- -------- NA For small vertical fenestration assemblies(rough opening less C405.2.4.3 Sidelight and toplight than 10 percent of primary daylight zone)where daylight responsive controls are not required,provide fenestration area to daylight zone calculation(s) Indicate on plans lighting zone(s)served by daylight responsive controls; ------- -------- ------ Identify sidelight and toplight daylight zones that are not provided with daylight sensing controls and the exception(s) Daylight responsive that apply________ _ _ _ _ _ _ _ NA C405.2.4 ------------ ------- controls Indicate on plans the lighting load reduction method- continuous dimming,or stepped dimming that provides at least iwo even steps beiween 0%-100%of rated power; Indicate that daylight sensing controls are configured to completely shut off all controlled lights in the lighting zone Additional controls- Identify spaces and lighting fixtures on plans that require NA C4052.5 Specifc application specific application lighting controls per this section lighting controls Indicate on plans that display and accent lighting,and display C405.2.5- Display and accent case lighting are controlled independently from both general NA area lighting and other lighting applications within the same Items 1&2 lighting space; Indicate manual and automatic lighting control method � l� � � � . _ ..