9602 EVERGREEN WAY 2017 Plans 2022-12-05

ICC A117.1-2009 ;� Chapter 9.Built-in Furnishings antl Equipment ' q$ , � LL t r a ilt-i rn�shin s :. r�; i �, ; t . . � : 901 Cenerai ' 903'Benches 909,1 Scope: Built-in furnishings and equi�pment 903.1 General. Accessible benches shail comply with required to be accessible by the scoping provisions Section 903. . ,, , , ;; _ adopted by the administrative authority shall comply g03.2 Clear Floor Space. A clear floor space comply- with the applicable provisions of Chapter 9. ing with Section 305, positioned for parallel approach to 902 Dining Surgaces and Work Surfaces the bench seat, shall be provided. � � ' 902.1 General. Accessible dinin surfaces and work 903.3 Si�e. Benches shall have seafs 42 inches (1065 g mm) minimum in length,'and 20 inches (510 mm) mini- surfaces shall comply with Section 902. ` mum and 24 inches (610 mm)maximum in depth. EXCE�T90fV: Dining surfaces and work surfaces pri- g03.4 �ack Support. The bench shall provide for back. marily for children's use shall be permitted to comply support or shall be affixed to a wall. Back support shall ' with Section 902.5. . be 42 inches (1065 mm) minimum in length,and shal( ` 902.2 Clear �loo� Space. A clear floor space comply- extend from a point 2 inches (51 'mm) maxirrium`above ing with Section 305, positioned for a forward approach, the,seat surface to a point 18 inches (455 mm) mini-. shall be provided. Knee and toe clearance complying mum above the seat surface. Back support shall be 2'/2 with Section 306 shall be provided. , inches (64 mm) maximum from the rear.edge of the ��p�-8��r: seat measured horizontally. - 1. At drink'surfaces 12 inches(305 mm)or less in g03.5 Height. The"top of the bench seat 'shall be 17 depth, knee and toe space shall not be inches (430 mm) minimum and 19 inches (485 mm) required to extend beneath the surface beyond maximum above the floor, measured to the top of the the depth of the drink surface provided. seat. 2. Dining surfaces�that are 15 inches (380 mm) '' �XCEPTION: Benches primarily for children's use � minimum and 24 inches (610 mm) maximum in shall be permitted to be 11 inches (280 mm) mini- � height are permitted to `have "a clear floor ' mum and 17 inches (430 mm) maximum above the space complying with Section 305 positioned floor, measured to the top of the seat. for a parallel approach. 903.6 5tructural Strength.Allowable stresses shall not 902.3 Exposecl Surfaces. There shall be n�o sharp or 'be exceeded for materials used where a vertical or hori- abrasive surfaces under the exposed portions of dining zontal force of 250 pounds (1112 N) is applied at any surfaces and work surfaces. point on the seat, fastener mounting device, or support- '-- ing structure. 902.4 Height.The tops of dining surfaces and work sur- faces shall be 28 inches (710 mm) minimum and 34 903.7 Wet Locations. Where provided in wet locations inches (865 mm) maximum in height above the floor, the surface of the seat shall be slip resistant and shall not accumulate water. 902.5 Dining Surfaces and �/ork Surfaces for Chil� el�en's Use. ,4ccessible dining surfaces and work sur- 904 Sales and Service Counters faces primarily for children's use shall comply with Section 902.5. 904.i General. Accessible sales and service counters �XCEPl'60(V: Dining surfaces and work surfaces , and windows shall comply with Section 904 as applica- used primarily by children ages 5 and younger shall ble. � • ` not be required to comply with Section 902.5 where a ��CEP710N: Drive up only sales or service counters clear floor space complying with Section 305 is pro- and windows are not required to comply with Section vided and is positioned for a parallel approach. ; 904. 902.5.1 Clea�Floor Space. A clear floor space com- 904,2 Approach.All portions of counters required to be plying with Section 305, positioned for forward accessible shall be located adjacent to a walking sur- approach, shall be provided. Knee and toe clearance face complying with Section 403. complying with Section 306 shall be provided. 904.3 Sales and �ervice Counters. Sales and service EXCEP`TIOiV: A knee clearance of 24 inches (610 counters shall comply with Section 904.3.1 or 904.3.2. mm) minimum above the floor shall be permitted. The accessible portion of the countertop shall extend ;902e5.2 hleight.The tops of tables and counters shall the same depth as the'sales and service countertop. � be 26 inches (660 mm) minimum and 30 inches (760 904.3.1 Parallel Approach. A portion of the counter - - mm) maximum above the floor. ` �� 'surface 36 in'ches (915 mm) minimum in length and 36 inches (915 mm) maximum in height above the 87