3500 TERMINAL AVE 2018-06-08 - Laserfiche WebLink

HD Fowler Company Submittal-Bid Item#27 W — — — CL TYTON JOINT® PipeCL m �_ • co 2013 EDITION P3 TYTON JOINT Pipe MON JOINT is U.S.Pipe's trademark for pipe with a push-on type connection.Simplicity, sturdiness and water-tightness of the system are built into the system by design.Convincing ANSI/AWWA C1511A21.5,Ductile-Iron Pipe, proof of its worldwide acceptance is shown by the fact that more than 95%of the pipe now sold Centrifugally Cast for Water. b¢U.S.Pipe is TYTON JOINT Pipe. Ductile Iron TYTON JOINT Pipe is centrifugally MON JOINT Pipe is available in sizes 3"through 64".Sizes 3"through 42"are available in cast in metal molds in accordance with ANSI/ nominal 18-foot laying lengths.6"through 24"sizes along with sizes 48"through 64"are AWWA C151/A21.5. available in nominal 20foot laying lengths. The asphaltic outside coating is in accordance MON JOINT Pipe in sizes 4"through 36"are UL Listed and sizes 4"through 16"are FM Approved: with'ANSI/AWWA C151/A2151. When MON JOINT Pipe are used for bridge crossings or other above-ground installations,each As specified in ANSI/AWWA C151/A21.51, length of pipe must be supported in a manner to restrict both vertical and horizontal movement: pipe weights have been calculated using standard barrel weights and weights of TYTON®Gasket is the only accessory required when installing MON JOINT Pipe.It is a circular bells being produced. rubber gasket which has a modified bulb shape in cross section.Gaskets are furnished in accordance with ANSI/AWWA C111/A21.1.Composition and dimensions of the gasket have been ANSI/AWWA C104/A21.4,Cement-Mortar carefully engineered to ensure a water-tight and lasting seal.The standard TYTON Gasket is Lining For Ductile-Iron Pipe and Fittings manufactured of SBR-styrene butadiene rubber.Gaskets of special elastomers may be ordered For-Water. for special applications.The gasket contour and bell socket contour ensure that the gasket will The cement-mortar lining and inside coating remain seated during proper assembly of the pipe.When joint restraint is required for push-on are in accordance with ANSI/AWWA C104/A21.4. joint pipe,two options are available from U.S.Pipe.For joint restraint of 4"through 24", Special linings and/or coatings can be FIELD LOK 350®Gaskets may be used and for joint restraint for 30"and 36",FIELD LOK®Gaskets furnished for specific conditions. may be used.FIELD LOK 350 Gaskets are rated for 350 psi in sizes 4"through 24".In addition,for — 4"through 36"sizes,TR FLEX Pipe and Fittings may be used and for 30"through 64"sizes, ANSI/AWWA;C111/A21.11,Rubber-Gasket HP LOK®Pipe and Fittings may be used.TR FLEX Pipe and Fittings are rated for working Joints for Ductile-Iron Pressure Pipe pressures for 350 psi in 4"through 24"sizes,250 psi in sizes 30"through 36"and for and Fittings. HP LOK Pipe and Fittings,the working pressure is 350 psi for 30"through 64".For higher TYTON®Gaskets are furnished in accordance pressure applications contact your U.S.Pipe representative.Complete details on both with ANSI/AWWA 01111A2111. FIELD LOK 350 Gaskets and TR FLEX Pipe and Fittings can be found on our website, www.uspipe.com. ANSI/AWWA G105/A21.5,Polyethylene Encasement for Ductile Iron Pipe Systems. NOTE:U.S Pipe qualifies for Federal Procurement under Public Law No.94-580,Section 6002, known as the Resource Recovery Act of 1976,since,due to modern technology,recycled'iron If specifiers ani!users believe that corrosive and steel scrap is used to a large degree in our Ductile Iron Pipe production. soil will be encountered where our products The plain end of the pipe is furnished beveled or with a quarter ellipse on the edge to allow assem are to be installed,please refer to bly.More than 40 years of successful experience have proved its sealing capabilities.Hydrostatic ANSI/AWWA C105/A21.5;for proper external tests have shown that the system will withstand pressures far in excess of rated pressures. protection procedures. ASTM A746-03"Standard specification for Ductile Iron Gravity Sewer Pipe." ASTM A716-08'Standard Specification for Ductile Iron Culvert.Pipe." TYTON®, TYTON JOINT®,TR FLEX®and FIELD LOK 350®are Registered Trademarks ASTM A536,"Standard Specification for of U.S.Pipe and Foundry Company,LLC. Ductile Iron,Castings." U.S.PIPE AND FOUNDRY CO. MON JOINT Pipe BRO-003 REVISED 1.13