Laserfiche WebLink
Smart Energy Today Inc. <br /> SOLAR <br /> 1001 Cooper Point Rd SW. <br /> 3 I Tilt Leg Installation Guinl. 4 I Tilt Leg Installation Guide Suite 140-290 <br /> Olympia,WA 98502 <br /> Phone:888-405-8689 <br /> 5. Component List Fax:855-350-9430 <br /> support smartenergytoday.net <br /> Component List Qty Part Number <br /> Tilt Leg Kit 1 51-7206-000 REVISIONS <br /> Long Leg 1 51-7200-xxx t. Place the Long Leg In the center of the U-Foot. DESCRIPTION DATE Rev <br /> Short Leg 1 51-7200-006 Align the slot of the Long Leg with the hole In IMOAL 1.21-2017 00 <br /> U-Foot 2 51-7100-001 the U-Foot.Insert a 3/8.16 x 2.5"hex head bolt <br /> with washer Into the hole and loosely attach <br /> 3/8-16x 2.5"S5 Hex Head Bolt 4 23-3716-250 a 3/8"flange nut.Do not tighten completely. - <br /> 318'55 Flat Washer 2 25-3702-000 Pivot the Long Leg onto the roof north of the Signature with Seal <br /> 3/8-36 SS Serrated Flange Nut 4 25-2501-016 array. jj71 <br /> 6. Assembly <br /> 1. Mount all U-Feet to the roof in the desired <br /> locations.Please note the orientation of both <br /> U-Feet in Figure 1. <br /> Fig.3 PROJECT NAME 8 ADDRESS <br /> Note:Determine the maximum distance <br /> beween U-feet according to engineering 6� 1 3. Attach the Short Leg to the front XR rail in your <br /> specifications.In addition,please be aware that XR assembly(created according to the XR Solar <br /> the placement of the XR rails vary by module 1 Rail System Installation Manuals)using the <br /> manufacturer.Set your XR rail spacing(North �.V normal method of sliding bolts into the 3/8' <br /> to South).The maximum distance the XR rails .- channel(shown In same Installation Manual). • <br /> can be placed from the edge of the module is "4- n Leave nut finger tight to assist In aligning with Q <br /> 15%of the modules length,as shown in Figure U-foot previously attached on roof. ;j <br /> 2.On the South side,the rail might require <br /> placement near the edge of the module to • Q <br /> avoid the module'crashing'into the roof as you 'row, I— o NM ao <br /> tilt the assembly. Fig.1 % ~ ZZ SC) <br /> 0 Q } N <br /> Fig. <br /> 4 CC} Q vr <br /> 15%MAX , 2 I-LLI <br /> �.., 4. Attach the Short Leg to the U-foot by aligning Q a W ZO <br /> PANS.LENGTH the hole in U-foot with the slot in Short Leg $ ti ` F-- r>LL 2 <br /> N, and inserting a 3/8-16 X 25"hex head bolt - 1 <br /> F RAIL and washer.Figure <br /> 5. attach 3/8"Flange nut as Uw.I n' <br /> \�(7 shown in Figure 5. 7. i <br /> \\ \N\15%MAX; lam~ <br /> NN ___. <br /> — UP TO -4* <br /> �- <br /> 15%OF PANEL <br /> LENGTH MAX. �r <br /> ' Jr <br /> SHEET NAME <br /> 1.; Fig.5 EQUIPMENT <br /> SPECIFICATION <br /> SHEET SIZE <br /> ANSI B <br /> IronRiilge 291 Shell Ln.Willits,CA 95490 (707)459-9523 72017071459-1833 www.lsonRidge.com irenRidge 291 Shell ln.WIIIIIt.CA 95490 17071 459-9523 Fax(707)459-1833 erww.IronRidge.com 11'_X 17" <br /> SHEET NJI.IBER <br /> PV-11 <br />