|
OISN I AREA OF WORK
<br />i
<br />OFFICE
<br />} OFFICE
<br />---------------
<br />--------- -- -- 1456 1
<br />6 12,
<br />I Afi
<br />in I d/ OFFICE
<br />[ " _ OPENmm
<br />SFC
<br />A 14.8 - B• A T455 r 'i •!• t• ; r i r / .'f
<br />e
<br />CO n6 e.
<br />.r.. MIN. SI
<br />I
<br />s1oR 5
<br />MCI 1451 r
<br />--1r A6 C E
<br />'
<br />(D)
<br />OF
<br />CA)
<br />,
<br />PAR
<br />TITION N PLAN NOTES
<br />I :t
<br />1. DO NOT SCALE DRAWINGS, WRITTEN DIMENSIONS GOVERN ALL 6• MODIFY EXISTING FLOOrt SURFACES AS REQUIRED TO INSTALL NEW 13. REFER TO POWER & SIGNAL AND REFLECTED CEILING PLAN
<br />PARTITION LOCATIONS SHALL BE AS SHOWN ON PARTITION PLAN. IN FLOORING MATERIALS, THUS PREVENTING NOTICEABLE LUMPS OR DEPRESSIONS. SWITCHES AND OUTLETS TO BE REMOVED. PATCH AND REF
<br />CASE OF CONFLICT NOTIFY ARCHITECT. PARTITION PLAN BY ARCHITECT TO MATCH ADJACENT SURFACE AND FINISH.
<br />TAKES PRECEDENCE OVER ALL OTHER PLANS. 7. NOTIFY ARCHITECT IN WRITING OF ANY DISCREPANCIES OR CONFLICTS
<br />IN THE LOCATION(S) OF NEW CONSTRUCTION. UPON COMPLETION OF PARTITION 14. OBTAIN APPROVAL FROM ARCHITECT PRIOR TO MODIFYING
<br />2. ALL GYPSUM BOARD PARTITIONS SHALL BE TAPED, SPACKLED AND SANDED LAYOUT, NOTIFY ARCHITECT, VERIFICATION OF THE LAYOUT TO BE
<br />SMOOTFI WITH NO MSI8LE JOINTS. PATCH AND REPAIR SURFACES TO MATCH PROVIDED BY THE ARCHITECT PRIOR TO PARTITION INSTALLATION 15, ALL EXISTING AND NEW FLOOR SLAB PENETRATIONS FOR F
<br />ADJACENT OR ADJOINING SURFACES WHERE REQUIRED. ALL FULLY PACKED AND SEALED IN ACCORDANCE VATH THE 0
<br />SURFACES SHALL @E ALIGNED. 8. ALL EXPOSED GYPSUM BOARD EDGES TO HAVE METAL EDGE TRIM.
<br />AND FIRE CODES.
<br />! 3. ALL PARTITIONS ARE DIMENSIONED FROM FINISH FACE OF GYPSUM BOARD TO 9. ALL WORK SHALL BE ERECTED AND INSTALLED PLUMB, LEVEL, SQUARE
<br />AND TRUE. 16. TRIM THE BOTTOMS OF DOORS TO CLEAR THE TOP OF FIN
<br />FINISH FACE OF GYPSUM BOARD UNLESS OTHERWISE NOTED. ALL AS APPLICABLE, BY 1/4' INCH MAXIMUM, UNLESS OTHER*
<br />DIMENSIONS MARKED "CLEAR' OR "CLR" SHALL BE MAINTAINEO AND SHALL ALLOW 10. REFER TO MILLWORK SHOP DRAWINGS FOR SPECIFIC DETAILS OF COORDINATION SLAB CONDITIONS.
<br />z . FOR THICKNESSES OF ALL WALL FINISHES, U.O.N. BETWEEN DRYWALL/MILLWORK CONDITIONS,
<br />17, ALL CLASS SHALL 8E CLEAR TEMPERED CLASS, UNLESS 0
<br />A
<br />4. DIMENSIONS NOTED "CLEAR" OR "CLR" MUST BE ACCURATELY 11. REFER TO REFLECTED CEILING PLANS FOR SOFFITS, CEILING HEIGHTS AND NOTED LTONG MARKS SHALL NOT VISIBLE. CLE
<br />MAINTAINED, AND SHALL NOT VARY MORE THAN k 1/8" PLENUM BARRIER LOCATIONS. POLISH ALLL GLALA55 PRIOR TO PROJECT DELIVV ERY.
<br />WITHOUT WRITTEN INSTRUCTION FROM ARCHITECT. 18, CLG. HT. PARTITIONS SHALL BE INSTALLED TIGHT TO FINISI
<br />i 12. REFER TO SHEET AN FOR ADDITIONAL NOTES, LEGENDS, SYMBOLS, WI111 NO JOINTS VARYING MORE THAN 1/e" OVER 6'-0" A
<br />5. DIMENSIONS MARKED T MEAN A TOLERANCE NOT GREATER NOR SMALLER ABBREVIATIONS, AND SCHEDULES. JOINTS GREATER THAN 3/16", U.O,N.
<br />THAN 2 INCHES FROM INDICATED DIMENSION, U.O.N. VERIFY FIELD
<br />' DIMENSIONS EXCEEDING TOLERANCE WITH THE ARCHITECT,
<br />SECURE ARCHITECT'S APPROVAL.
<br />�.
<br />DOOR/HARDWARE/DESCRIPTION/SCHEDULE NOTES: 1. ALL 20. MIN. RATED DOOR do FRAME ASSEMBLIES SHALL BE U.L. APPROVED 2. ALL DOOR k DOOR FRAMES ARE TO BE STAINED WOOD TO MATCH ARCI
<br />DOOR TYPE DESCRIPTION HARDWARE SCHEDULE
<br />A SINGLE 3'-0' X 7'-0" X 1-3/4" SOLID CORE WOOD VENEER DOOR. GROUP DESCRIPTION
<br />IN WOOD FRAME TO BE W- t REF. 3,5,6/0.2
<br />1 1/2 PAIR BUTT HINGES
<br />1 EACH LATCHSET
<br />€ B SINGLE 3'-0" X 8'-0" X 1 3 4" WOOD DOOR `J 1 EACH DOOR STOP
<br />CORRIDOR SIDE TO MATCH BLDG. STO. 1 EACH COAT HOOK (A PRIVATE OFFICE DOORS ONLY)
<br />TENANT SIDE TO BE W-1. DOOR & FRAME TO BE 20 MEN, RATED j'\ 1 1/2 PAIR BUTT HINGES
<br />SFE DETAIL 13/ A8,2 f-;7 1 EACH LOCKSET
<br />1 EACH DOOR STOP
<br />f 1 EACH COAT HOCK (® PRIVATE OFFICE DOORS ONLY)'"
<br />eEXISTING EXISTING DOOR, FRAME, AND HARDWARE TO REMAIN.
<br />HARDWARE PER BUILDING STD.
<br />I•
<br />NOTES:
<br />t. ALL 20 MIN. DOORS do FRAME SHALL BE U.L. LISTED
<br />2• ALLDOOR FRAMES ARE TO BE STAINED TO MATCH ARCHITECT'S SAMPLE U.O.N.
<br />r r r r r.jr i r i r i i i= i r r i Ai
<br />30 29 28 2.7 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 MICROBOX
<br />,
<br />13
<br />-
<br />Merrill hynch
<br />r
<br />MERRILL LYNCH & CO. , INC.
<br />;! , i.•/, •.� r•�✓ , ,� ,'' :� fir'.
<br />r'
<br />EVERETT MUTUAL TOWER
<br />'; '' ✓- '
<br />SUITE 1401
<br />EVERETT WASHINGTON
<br />i
<br />• �,
<br />r
<br />EXPANSION SPACE
<br />:i
<br />■-
<br />..
<br />- - -
<br />SHEET
<br />NOTES
<br />2 100% CL" REVEW 4.11.95
<br />'
<br />1 50% G." "W 3.30.95
<br />)CATIONS OF
<br />19. DIMENSIONS LOCATING DOORS ARE TO THE INSIDE EDGE OF
<br />Issue Description Dote
<br />€IriON
<br />JAMB. U.O.N.
<br />1. CONTRACTOR TO REMOVE (E) WINDOW BLINDS, AS REQUIRED
<br />-URRING• 20. "ALIGN" MEANS TO ACCURATELY LOCATE FINISHED FACES IN THE SAME
<br />WITHIN
<br />CLEAN
<br />AREA OF WORK, STORE IN SAFE, CLEAN ENVIRONMENT AND
<br />BEFORE REINSTALLATION.
<br />'
<br />PLANE.
<br />IA
<br />4LL BE
<br />BUILDING 21. ALL MILLWORK TO BE FASTENED TO THE PARTITION. PROVIDE BLOCKING
<br />FOR ALL MILLWORK NOT SUPPORTED BY SLABS OR ABOVE 4'-0" HT,
<br />ALL CONCEALED LUMBER & BLOCKING TO BE FIRE TREATED.
<br />N T E R O R
<br />)OR,
<br />1. VERIFY 22. ALL DOORS SHALL HAVE 1'-6" CLR. ON STRIKE/PULL SIDE OF DOOR.
<br />VERIFY AND ADVISE ARCHITECT OF EXCEPTIONS PRIOR TO CLOSING OUT
<br />1
<br />PARTITIONS.
<br />``
<br />A R C H f T E C T S
<br />n _
<br />23. CONTRACTOR TO PROVIDE SHOP DRAWINGS FOR:
<br />• MILLWORK
<br />• CARPET SEAMING
<br />N C
<br />j
<br />24. ALL PLYWOOD TO BE FIRE TREATED IN ACCORDANCE W/ LOCAL CODE.
<br />I
<br />350 CALFORNA STREET, SUTE 1500
<br />SAN FRANOSCO, CALFC" 94U4
<br />415.434.3305 FAX 415.434.=
<br />,
<br />;AMPLE U.D.N. LEGEND
<br />E DESCRIPTION
<br />EXISTING CONSTRUCTION TO REMAIN
<br />;T HAGER 881193-4 1/2 X 4 1/2
<br />PARTITION TO REMAIN,
<br />�,,,�� ,�,� w� � N I4
<br />ALL � us � r
<br />y��
<br />OP HAGER FB15: FB16 *CARPETED AREAS
<br />ET SCHLAGE L9010 W LEVER TYPE 17
<br />REF, 1/A8.1
<br />NON -RATED CEILING HEIGHT PARTITION
<br />T SCHLAGE L9050 W/ LEVER TYPE 17
<br />Architect: DAVD B. MOLR14V0 206-M 5749
<br />LOW HEIGHT PARTITION (4'-0' HIGH)
<br />REF. 5,6,7/A8.1
<br />_
<br />ULL TYDIX 61064 US320
<br />LATCH GLYNN JOHNSON GJ 30-US320
<br />REF. 4/A8.1
<br />NON-RATED PARTITION EXTENDED 6" ABOVE CEILING HEIGHT
<br />-,
<br />•, i
<br />IOK PETER PEPPER 2039A BLACK 1" DIA. X 2 1/2'
<br />R8.EF. 17/A1
<br />FURRED PARTITION
<br />.'
<br />'
<br />GLAZED PARTFTION W/ FRAME
<br />Drown: RZ _ - Check: AW/AB/JM
<br />- -
<br />REF. SHEET A8.2
<br />;4''
<br />ALIGN SURFACES AS INDICATED
<br />Job No: 24046,06 SCO14: VB' T"0�
<br />'•i
<br />ya
<br />-L HARDWARE FINISH SHALL BE US320 SATIN STAINLESS U.O.N.
<br />1 .�t`W�t `,
<br />MILLWORK
<br />1i
<br />HARDWARE
<br />D VENEER CABINET DOORS, U.O.N.: FLUSH RECESSED ADJUSTABLE STANDARDS:
<br />RMS +' SURFACES HC216 KV #255 W/ #256 BRACKETS
<br />ONE -HOUR RATED SLAB TO SLAB ACOUSTICAL PARTITION
<br />�; �� CAppROF EVERETT
<br />OVED FOR
<br />)E OF DOOR AT TOP FOR BASE CABINETS
<br />)E OF DOOR AT BOTTOM FOR OVERHEAD CAT,iINETS DRAWER SLIDES:
<br />REF. 8,9,10,11/AB.1
<br />BUILUMV
<br />DATE -------
<br />;TIC LAMINATE CABINET DOORS, U,O.N,: GRANT #329 FULL EXTENSION
<br />W W 538/8 2-3/8'
<br />P CORNER OF DOOR FOR BASE CABINETS
<br />CORNER DF DOOR FpR OVERHEAD CABINETS
<br />2707 ColbyAve14AlITTOM
<br />9Y
<br />)NCEALEO HAFELE TYPE HINGES FOR ALL CABINET DOORS L1.O.N.
<br />Sheet:
<br />k
<br />6 7 8
<br />-.tip.•
<br />9 10
<br />11 12 13 14 15 16
<br />---__
<br />17
<br />_-
<br />18 19 20 21 22
<br />-
<br />23 24 25 26 27 28 29 3
<br />
|