824 W CASINO RD BASE FILE 2018-12-27

Building Permit Plans Checklist, pg. 1 ENV-CHK 2015 WSEC Compliance Forms for Commercial Buildings including R2,R3,&R4 over 3 stories and all R1 Revised Jun 2016 Project Title: Avaire Apartments Renovation Date 03/30/2017 The following information is necessary to check a building permit application for compliance with the building envelope requirements in the Washington State Energy Code,Commercial Provisions. Applicability Code Location in Building (yes,no,na) Section Component Compliance information required in permit documents Documents Department Notes SCOPE Low energy spaces are identified on plans;include project information, No C402.1.1 Low energy spaces and calculations if applicable,that demonstrate spaces are eligible for envelope provisions exemption No 0402.1.1.1 Semi-heated spaces Semi-heated spaces are identified on plans,include calculations that demonstrate spaces are eligible for wall insulation exemption Provide building area,average wall and roof U-factor,and installed yes C402.1.2 Equipment Buildings equipment information that demonstrates equipment building is eligible for A5.5 envelope provision exemption Walk-in and Cooler and freezer spaces are identified on plans;C410 envelope No C410.2 warehouse cooler and freezer spaces compliance forms provided(pending) No C101.4.1 Mixed occupancy Spaces with different occupancy requirements are identified on plans Existing unconditioned spaces changing to semi-heated or conditioned No 0503.2 Change of space space,and existing semi-heated spaces changing to conditioned space, conditioning are identified on plans.Include calculations that demonstrate baseline and final level of conditioning. Existing F,S and U-occupancy spaces undergoing a change in occupancy yes are indicated on plans;include calculations that demonstrate upgrade AO complies with the current WSEC. Change of Pre-2002 Group R spaces undergoing a change to a commercial No C505.1 occupancy are indicated on plans;include calculations that demonstrate occupancy upgrade complies with the current WSEC. Non-Group R occupancy spaces undergoing a change to Group R are No indicated on plans;include calculations that demonstrate upgrade complies with the current WSEC. ENVELOPE PROVISIONS Indicate envelope insulation compliance path and provide applicable No forms;ENV-PRESCRIPTIVE or ENV-UA/ENV-SHGC for component C103.2 Compliance performance C103.6.3 documentation No If complying via total buidling performance,provide a list of all proposed envelope component types,areas and U-values C303.1.1 Insulation Indicate identification mark shall be applied to all insulation materials and yes 0303.1.2 identification insulation installed such that the mark is readily observable during inspection AO yes C303.1.3 Fenestration product Fenestration products shall be labeled with rated U-factor,SHGC,VT,and C402.4.3 rating leakage rating AO yes Indicate installation methods,thicknesses,densities and clearances to 0303.1.1 General insulation achieve the intended R-value of all insulation materials; No C402.2.1 installation Where two or more layers of rigid insulation will be used,indicate that edge joints between layers are staggered A5.5 No Indicate R-value(s)of cavity/continuous insulation on roof sections; No Indicate framing materials on roof sections; No Indicate method of framing for ceilings below vented attics and vaulted ceilings per A102.2(std,adv); No C103.2 Roof assembly Provide area weighted average U-factor calculation for insulation whose C402.2.2 insulation thickness varies by 1 inch or less; Indicate effective U-factors of tapered insulation entirely above deck per No A102.2.6;include roof configuration and slope,maximum R-value at peak and minimum R-value at low point for all roof surfaces No Indicate R-values for thermal spacers and each insulation layer,and liner system(LS)method for metal building roofs No 0402.2.2 Skylight curb Indicate curb insulation R-value on roof section if not included in skylight insulation NFRC rating yes Indicate R-value(s)of cavity/continuous insulation on wall sections; yes Indicate framing materials on wall sections; yes Indicate method of framing for wood const per A103.2(std,int,adv); C103.2 Indicate material density category,wall weight and heat capacity for yes C402.2.3 Above/below grade qualifying mass walls; C402.2.4 wall insulation C303.2.1 For qualifying ASTM C90 masonry walls,indicate loose-fill core insulation yes material and percentage of cores filled including grouted cores,bond beams,vertical fills,headers and any other grouted cores;