4812 ELM ST 2019-01-28 - Laserfiche WebLink

Job Truss Truss Type Qty Ply submittals 111803709 BB706360 CO3 Common 1 1 Job Reference(optional) The Truss Co., Burlington,WA,98233 8.030 s Oct 5 2016 MiTek Industries,Inc.Tue Jul 11 09:40:57 2017 Page 1 ID:DYVe4WH3wNiyn_iNU 1 ZZcRz3MY8-?RTwiuBVhAJZ7Gb4ITTTJiadLC27Jb7CSIHc4lyzAi4 1 4-10-4 I 9-2-0 I 13-5-12 I 18-4-0. I 4-10-4 4-3-12 4-3-12 4-10-4 4x4 = Scale=1:37.3 3 6.00 112 7 8 2x4 2x4 i 2 4 N, .1 v v W1 1 5 71 w EL to 6 4x4 = 4x4= 3x8 =- I I 9-2-0 I 18-4-0 I 9-2-0 9-2-0 Plate Offsets(X,Y)-- [1:0-1-8,Edge],[5:0-1-8,Edge] LOADING (psf) SPACING- 2-0-0 CSI. DEFL. in (loc) 1/deft L/d PLATES GRIP TCLL 25.0 Plate Grip DOL 1.15 TC 0.30 Vert(LL) -0.13 1-6 >999 240 MT20 185/148 (Roof Snow=25.0) Lumber DOL 1.15 BC 0.60 Vert(CT) -0.24 1-6 >888 180 TCDL 8.0 Rep Stress Incr YES WB 0.18 Horz(CT) 0.03 5 n/a n/a BCLL 0.0 * Code IRC2015/TP12014 Matrix-SH Weight:64 lb FT=20% BCDL 7.0 LUMBER- BRACING- TOP CHORD 2x4 HF No.2 TOP CHORD Structural wood sheathing directly applied or 4-9-2 oc purlins. BOT CHORD 2x4 HF No.2 BOT CHORD Rigid ceiling directly applied or 8-6-10 oc bracing. WEBS 2x4 DF Stud MiTek recommends that Stabilizers and required cross bracing be installed during truss erection,in accordance with Stabilizer Installation guide. REACTIONS. (lb/size) 1=722/0-3-8 (min.0-1-8),5=722/0-3-8 (min.0-1-8) Max Horz 1=-104(LC 11) Max Uplift 1=-255(LC 10),5=-255(LC 11) FORCES. (Ib)-Max.Comp./Max.Ten.-All forces 250(Ib)or less except when shown. TOP CHORD 1-2=-1234/443,2-7=-906/299,3-7=-831/310,3-8=-831/310,4-8=-906/299, 4-5=-1234/443 BOT CHORD 1-6=-430/1057,5-6=326/1057 WEBS 3-6=-130/487,4-6=-392/300,2-6=-392/299 NOTES- 1)Wind:ASCE 7-10;Vult=130mph(3-second gust)Vasd=103mph;TCDL=4.2psf;BCDL=4.2psf;h=25ft;Cat.II;Exp C;enclosed; MWFRS(envelope)gable end zone;cantilever left and right exposed;end vertical left and right exposed;Lumber DOL=1.60 plate grip DOL=1.60 2)TCLL:ASCE 7-10;Pf=25.0 psf(flat roof snow);Category II;Exp C;Partially Exp.;Ct=1.1 3)Unbalanced snow loads have been considered for this design. 4)This truss has been designed for a 10.0 psf bottom chord live load nonconcurrent with any other live loads. 5)*This truss has been designed for a live load of 23.Opsf on the bottom chord in all areas where a rectangle 3-6-0 tall by 2-0-0 wide will fit between the bottom chord and any other members. 6) Provide mechanical connection(by others)of truss to bearing plate capable of withstanding 100 lb uplift at joint(s)except(jt=lb) 1=255,5=255. LOAD CASE(S) Standard 'i L. P(} "., ,, , . " , t 4,;1611, V. xT 19969 July 11,2017 t t © WARNING-Verify design parameters and READ NOTES ON THIS AND INCLUDED MITER REFERENCE PAGE M11.7473 BEFORE USE. Design valid for use only with MiTek connectors.This design is based only upon parameters shown,and is for an individual building component. Applicability of design paramenters and proper incorporation of component is responsibility of building designer-not truss designer.Bracing shown is for lateral support of individual web members only.Additional temporary bracing to insure stability during construction is the responsibillity of the erector,Additional permanent bracing of the overall structure is the responsibility of the building designer.For general guidance regarding fabrication,quality control,storage,delivery,erection and bracing,consult ANSIITPII Quality Criteria,DSB-89 and BCS11 Building Component �tf / � Safety Information available from Truss Plate Institute,583 D'Onofrio Drive,Madison,151 53719. theTRUSSco.RUSSco.INC. /`+/{1