5723 HIGHWAY PL 2019-03-06 - Laserfiche WebLink

Product data differences between the testing facilities. For best painting results, all surfaces, Thickness: 1/2" (12.7 mm) Assemblies are listed as "combustible" including joint compound,should be 5/8" (15.9 mm)Type X (wood framing) and "noncombustible" clean, dust free and not glossy. If glossy (concrete and/or steel construction). paints are used, a thin skim coat of Width:4' (1220 mm) standard For fire resistance ratings refer to the compound over the entire surface, Level Length:8', 10',12'standard Gypsum Association Fire Resistance 5 finish, is recommended to reduce (2440 mm, 3050 mm,3660 mm) Design Manual and UL Fire Resistance highlighting or joint photographing. Directory—Vol 1. This method is also recommended for Custom lengths available upon request. Contact the nearest Sales Office for areas of critical sidelighting of natural or stocked lengths available. Applicable Standards and artificial light sources. Weights (nominal): References 1/2"Regular 1.6 psf(7.8 kg/m2) • Meets ASTM C1396 and A sealer application under wallpaper or 5/8"Type X 2.2 psf(10.7 kg/m2) CAN/CSA-A82.27 other wall covering is also recommended • ASTM C840 so the board surface will not be damaged, Edge:Tapered • CAN/CSA-A82.31 Gypsum Board if the covering is subsequently removed Application during redecorating. Joint treatment must • Gypsum Association GA-216 be thoroughly dry before proceeding Technical Data • Gypsum Association GA-214 with primer-sealer application and final Composition and Materials • ICC International Building Code (IBC) decoration. Manufactured panel with gypsum core, • National Building Code of Canada encased in paper.Various additives are (NBCC) *The performance of CertainTeed added to the core to enhance moisture Moisture and Mold Resistant gypsum and fire resistive qualities. Installation board in actual use may not accurately Recommendations reproduce the results achieved in this Surface Burning Characteristics Installation of M2Tech Gypsum Board ASTM laboratory test. Good design and CertainTeed Moisture and Mold Resistant should be consistant with methods construction practices that prevent gypsum board has a Flame Spread described in the standards and referenc- water and moisture exposure of building ratings of 5 and Smoke Developed es noted. Cutting should be from the products are the most effective strategy ratings of 5 when tested in accordance face side of the boards for best results. to avoid the growth of mold. with ASTM E84, (UL 723, UBC 8-1, NFPA 255, CAN/ULC-S102). Decoration Notice M2Tech Gypsum Board accepts most The information in this document is Fire Resistance types of paints,texture and wall covering subject to change without notice. Fire resistance tests are conducted in materials.The surface shall be primed CertainTeed assumes no responsibility for accordance with ASTM E119, and sealed with a full-bodied latex any errors that may inadvertently appear (ANSI/UL263, UBC 7-1, NFPA 251, primer before applying a final decorative in this document: CAN/ULC-S101) and no warranty is material. This will equalize the suction made other than conformance to the between the joint compounds and the standard under the assembly. Minor paper surface. ak discrepancies may exist in the values of ratings, attributable to changes in materials and standards, as well as GREENGUARD --^'- �, nu PRODUCT CERTIFIED FOR ? ,se""4-e,'e, LOW CHEMICAL EMISSIONS f .,4 u'' ULCOM/G6 Wi �„ 11 • UL 2818 '',4,•:.:,.4),/ EMBER 0 ''''iiy aO4nydroBBP'5., GOLD ASK ABOUT ALL OF OUR OTHER CERTAINTEED® PRODUCTS AND SYSTEMS: CertainTeed Corporation ROOFING • SIDING • TRIM • DECKING • RAILING • FENCE P.O.Box 860 GYPSUM • CEILINGS • INSULATION Valley Forge, PA 79482 www.certainteed.com http://blog.certainteed.com Professional:800-233-8990 Consumer:800-782-8777 "' ' G12-2007 CertainTeed Gypsum.Rev 10-2014 Printed in U.S.A.on recycled paper.CTG-2403 ltd.... .