3003 W CASINO RD BLDG 40-54 2021-02-17

ESR-1917 I Most Widely Accepted and Trusted 4aage-5-of4.3 5.14 Use of anchors made of stainless steel as specified in 6.2 Quality-control documentation. this report are permitted for exterior exposure and 7.0 IDENTIFICATION damp environments. The anchors are identified by packaging labeled with the 5.15 Use of anchors made of stainless steel as specified in manufacturer's name (Hilti, Inc.) and contact information, this report are permitted for contact with preservative- anchor name, anchor size, and evaluation report number treated and fire-retardant-treated wood. (ESR-1917). The anchors have the fetters KB-TZ 5.16 Anchors are manufactured by Hilti AG under an embossed on the anchor stud and four notches approved quality-control program with inspections by embossed into the anchor head, and these are visible after ICC-ES. installation for verification. 6.0 EVIDENCE SUBMITTED 6.1 Data in accordance with the ICC-ES Acceptance \_ , Criteria for Mechanical Anchors in Concrete Elements (AC193),dated March 2012(ACI 355.2-07). TABLE 1--SETTING INFORMATION(CARBON STEEL AND STAINLESS STEEL ANCHORS) • SETTING Nominal anchor diameter(in.) INRORMATION Symbol Units _ 3/6 1/2 §/9 3/4 Anchor O.D. da In. 0.375 0.5 0.625 0.75 (d0 2 (mm) (9,5) (12.7) (15.9) (19.1) Nominal bit dart in. 3/6 1/2 5/ 3/ diameter $ a Effective min, hat In. 2 2 31/4 31/6 4 33/4 434. embedment (mm) (51) (51) (83) (79) (102) (95) (121) Nominal in. 26/16 23/6 35/8 36/16 47/16 46/16 56/re embedment hnom (mm) (59) (60) (91) (91) (113) (110) (142) I In. 264 26/8 4 33/4 43/4 41/2 53/4 Min.hole depth ho (mm) (67) (67) (102) (95) (121) (114) (146) Min.thickness of In. 1/4 3/4 1/4 3/6 3/4 116 16/s fastened part1 t'",, (mm) (6) (19) (6) (9) (19) (3) (41) Required ft-lb 25 40 60 110 Installation torque 7 n5r (Nm) (34) (54) (81) (149) Min.dia.of hole da In. 7/16 6/1e 11/1e 13/78 In fastened part (mm) (11.1) (14.3) (17.5) (20.6) Standard anchor In. 3 33/4 5 33/4 41/2 51/2 7 43/4. 6 91/2 10 51/2 8 10 lengths taneh (trim) (76) (95) (127) (95) (114) (140) (178) (121) (152) (216) (254) (140) (203) (254) Threaded length , In. ` 7/a 16/8 27/8 15/8 2318 33/6 47/8 11/2 23/4 51/4 63/4 11/3 4 6 (Incl.dog point) nread (mm) (22) (41) (73) (41) (60) (86) (124) (38) (70) (133) (171) (38) (102) (152) Unthreaded In. 21./6 21/6 31/4 4 length tunrhr (mm) (54) (54) (83) (102) 1The minimum thickness of the fastened part is based on use of the anchor at minimum embedment and is controlled by the length of thread.If a thinner fastening thickness is required,Increase the anchor embedment to suit. 2The notation in parenthesis is for the 2006 IBC.