3623 HOYT AVE 2020-01-17 - Laserfiche WebLink

Installation Data Required Centerline of Sprinkler Sprinkler Suggested Hole Diameter Installation Escutcheon or Cover Plate Tube/Inlet to Finished Ceiling Model in Wall or CeilingWrench Vertical Dimension* Standard Escutcheon 2-1/8"(54 mm) F3 or F3R HB Extended Escutcheon 2-1/2"(64 mm) F3QR56 DryF1 Recessed Escutcheon 2-1/4"(57 mm) Not Pendent Applicable FP Recessed Escutcheon XLO2 CCP Cover Plate 2-1/2"(64 mm) Standard Escutcheon 2-1/8"(54 mm) 4-5/8"to 12-5/8" HB Extended Escutcheon 2-1/2"(64 mm) (118 mm to 321 mm) F3 or F3R F3QR56 Dry Fl Recessed Escutcheon 2-1/4"(57 mm) cULus,NYC mm) 6-5/8" Horizontal FP Recessed Escutcheon 2-1/2"(64114-5/8"to 168 (118 mm to 168 mm) Sidewall XLO2 Fl Recessed Escutcheon 2-1/4"(57 mm) FM FP Recessed Escutcheon 2-1/2"(64 mm) 4-5/8"to 12-5/8" (118 mm to 321 mm) *Based on 5/8" (16 mm)centerline of sprinkler tube/inlet to defector vertical distance. Maintenance The Model F3QR56 Dry Sprinklers should be inspected and the sprinkler system maintained in accordance with NFPA 25. Do not remove the factory applied thermally sensitive wax 5. Sprinkler Temperature Rating: See Temperature Rat- I fillet between the bulb supporting cup and the wrenching ings table boss. Do not replace this wax with a substitute substance. 6. Sprinkler Finish: See Finishes Table An Alternate substance may interfere with proper operation 7. Escutcheon/Cover Plate Finish: See Finishes Table of the sprinkler. Do not clean sprinklers with soap and water, 8. Length: "A" Dimension (face of tee to face of ceiling ammonia or any other cleaning fluids. Remove dust by us- or wall) in 1/4" (6 mm) increments-See Fig. 1 through ing a soft brush or gently vacuuming. Replace any sprin- Fig. 9 kler which has been painted (other than factory applied) or Note: damaged in any way. A stock of spare sprinklers should be The "A" dimension is based on a nominally gauged pipe maintained to allow quick replacement of damaged or op- thread "make-up"of.600" (15mm) per ANSI B2.1 [approxi- erated sprinklers. Prior to installation, sprinklers should be mately 71/2 threads]. maintained in the original cartons and packaging until used to minimize the potential for damage to sprinklers that would cause improper operation or non-operation. Ordering Information Specify: 1. Sprinkler: [Model F3QR56 Dry Pendent SIN R5714] [Model F3QR56 Dry Horizontal Sidewall SIN R5734] 2. Escutcheon/Cover Plate: [None][Standard escutch- eon][Model HB extended escutcheon][Model Fl re- cessed escutcheon][Model FP recessed escutcheon] [Model CCP cover plate-pendent only] 3. Inlet Threads: [1" NPT][1S07-1R1][3/4" NPT][IS07- 1 R3/4] 4. Inlet Fitting: [Long -Standard Inlet Fitting][Short "PL" -Wet Pipe Systems only] The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association,Factory Mutual Research Corporation,or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable. Products manufactured and distributed by Reliable have been protecting life and property for almost 100 years,. Manufactured by Reliable Automatic Sprinkler Co.,Inc. N. Recycled ® (800)431-1588 Sales Offices Paper (800)848-6051 Sales Fax Revision lines indicate updated or new data. (914)829 2042 Corporate Offices www.reliablesprinkler.com Internet Address EG.Printed in U.S.A.11/18 P/N 9999970175