2320 106TH ST SW 2022-08-29 - Laserfiche WebLink

General CALIFORNIA PROPOSITION chamber,the moisture would settle 65 WARNING: to the bottom of the chamber and Information will This product moisture detectors. ,,„—re Installation: and related accessories contain II I I manual contains important chemicals known to the State of This circuit must be connected to a information for the safe use of California to cause cancer,birth sensing unit and signaling device. this product.Read this manual defects or other reproductive harm. This is supplied in a Hydromatic built completely and follow the control panel. instructions carefully.Reasonable The Pump Pump: care and safe methods relating to the installation and operation of Shipping: The submersible pump is supplied this product should be practiced. When unpacking unit check for for 1 and 3 phase,and for 200,230, Check local codes and requirements concealed damage.Claim for damage 460 or 575 volts.A power cable before installation. must be made at the receiving is supplied with the green wire end through the delivering carrier. for ground.Be sure green wire is Safety Warnings Damage cannot be processed from connected to a good ground such as DANGER: Risk of electrical the factory. water pipe or ground stake. shock or electrocution.May Pumps in Storage or Heat Sensors: result in serious injury or death Not Operating: All motors have heat sensor units or fire hazard.Installer must embedded in the motor winding to disconnect all electrical sources Pumps with carbon ceramic seals detect excessive heat.The sensors prior to installation,handling must have impellers manually automatically reset when motor cools or servicing.Only qualified rotated(6 revolutions) after setting to safe temperature. personnel may install this system. non-operational for 3 months or NFPA 70/National Electric Code longer and prior to electrical start-up. The sensors are connected in series (NEC) or local codes must be Pumps with tungsten carbide seals with the motor starter coil so that followed.System must be properly must have impellers manually the starter is tripped if heat sensor grounded according to NEC.Do rotated(6 revolutions) after setting opens.The motor starter is equipped n eft pump by power cord. non-operational for 3 weeks or with overload heaters so all normal 1I'I' 'I longer andprior to electrical start-up. overloads are protected by the starter. ---GER: Biohazard risk.Once g wastewater source has been Seal Failure: NOTE: Failure to install such a connected to system,biohazard risk device negates all warranties by exists.Installers) and/or service An electrode is installed in the seal Hydromatic. personnel must use proper personal chamber so if any water enters the protective equipment and follow chamber through the first seal the Once sensor resets,the starter is to be handling procedures per OSHA electrode will be energized,and reset for FM for continued operation 29 CFR 1910.1030 when handling a signal will be transmitted to the of the pump.This circuitry is supplied equipment after wastewater source sensing unit at ground surface, in a Hydromatic control panel. has been connected to system. causing an alarm function to energize. NOTE: Failure to install such DANGER: Risk of asphyxiation. In operation the seal failure unit circuitry would negate FM Installer(s)and/or service indicates only that there is some approvals and all warranties by personnel must use proper water in the seal chamber.The pump Hydromatic. personal protective equipment and will continue to operate without follow OSHA 29 CFR 1910.146 or damage but the seal should be Sump Level Control: OSHA 29 CFR 1926.Pump may be checked immediately after failure is The sump level is controlled by installed in a location classified as indicated. Hydromatic float switch controls. a confined space. NOTE• Failure to install such The float is held in position in the DANGER: Cutting risk.Risk of a device negates all warranties sump by a weight attached to the serious cutting or amputation by Hydromatic®. power cord above the float.The cord exists.Disconnect all power sources supports the float and is adjusted for prior to servicing the pump.Pump Seal Failure Probes: height from the surface. may start without warning. All hazardous location submersible Typical duplex systems use three pumps have two factory installed controls: one set at turn-off,one -ps are not approved for use set at turn-on for one pump,and i i i ii . moisture detectors (seal failure r i 1 s i 1 g pools,recreational probes).They are in a normally open, one set for turn-on for two pumps. • ..r installations,decorative series circuit in the seal chamber. Pumps alternate operation on each fountains or any installation Under normal operating conditions, successive cycle. where human contact with the the circuit remains open.If the lower pumped fluid is common. Two pumps operate together only seal leaks and moisture enters this if sump level rises to the third or 2