8615 7TH AVE SE 2021-02-26 - Laserfiche WebLink

Building Permit Plans Checklist, pg. 1 ENV-CHK 2015 WSEC Compliance Forms for Commercial Buildings including R2,R3,&R4 over 3 stories and all R1 Revised Oct 2017 Project Title: ST.MARY MAGDALEN CHURCH Date 02/12/2019 The following information is necessary to check a building permit application for compliance with the building envelope requirements in the Washington State Energy Code,Commercial Provisions. Applicability Code Location in Building (yes,no,na) Section Component Compliance information required in permit documents Documents Department Notes SCOPE Identify low energy spaces on plans;include project information,and NA C402.1.1 Low energy spaces calculations if applicable,that demonstrate spaces are eligible for envelope provisions exemption NA C402.1.1.1 Semi heated spaces Identify semi-heated spaces on plans,include calculations that demonstrate spaces are eligible for wall insulation exemption Provide building area,average wall and roof U-factor,and installed NA C402.1.2 Equipment Buildings equipment information that demonstrates equipment building is eligible for envelope provision exemption Walk-in and NA C410.2 warehouse cooler Identify walk-in and warehouse cooler and freezer spaces on plans and freezer spaces NA C101.4.1 Mixed occupancy Identify spaces with different occupancy requirements on plans Identify on plans existing unconditioned spaces changing to semi-heated Change of space or conditioned space,and existing semi-heated spaces changing to NA C503.2 conditioning conditioned space;provide calculations for existing and final level of space conditioning,and calculations that demonstrate alteration complies with current WSEC Identify on plans existing F,S and U-occupancy spaces undergoing a change in occupancy;provide calculations that demonstrate alteration . complies with the current WSEC Change of Identify on plans pre-2002 Group R spaces undergoing a change to a NA C505.1 commercial occupancy;provide calculations that demonstrate alteration occupancy complies with the current WSEC Identify on plans non-Group R occupancy spaces undergoing a change to Group R;provide calculations that demonstrate alteration complies with the current WSEC ENVELOPE PROVISIONS indicate envelope insuiation compliance patn and provide appncaeie C103.2 Compliance forms;ENV-PRESCRIPTIVE or ENV-UA/ENV-SHGC for component YES C103.6.3 documentation oarformancp Attached If complying via total building performance,provide a list of all proposed envelope component types,areas and U-values C303.1.1 Insulation Indicate identification mark shall be applied to all insulation materials and YES insulation installed such that the mark is readily observable during A1.1 C303.1.2 identification inspection YES C303.1.3 Fenestration product Fenestration products shall be labeled with rated U-factor,SHGC,VT,and A9.1 C402.4.3 rating leakage rating Indicate installation methods,thicknesses,densities and clearances to C303.1.1 General insulation achieve the intended R-value of all insulation materials; YES C402.2.1 installation Where two or more layers of rigid insulation will be used,indicate that A8.0 edge joints between layers are staggered Indicate R-value(s)of cavity/continuous insulation on roof sections; Indicate framing materials on roof sections; Indicate method of framing for ceilings below vented attics and vaulted ceilings per A102.2(std,adv); YES C103.2 Roof assembly Provide area weighted average U-factor calculation for insulation whose C402.2.2 insulation thickness varies by 1 inch or less; A5.2,A5.3,A8.0 Indicate effective U-factors of tapered insulation entirely above deck per A102.2.6;include roof configuration and slope,maximum R-value at peak and minimum R-value at low point for all roof surfaces Indicate R-values for thermal spacers and each insulation layer,and liner system(LS)method for metal building roofs NA C402.2.2 Skylight curb Indicate curb insulation R-value on roof section if not included in skylight insulation NFRC rating Indicate R-value(s)of cavity/continuous insulation on wall sections; Indicate framing materials on wall sections; Indicate method of framing for wood construction per A103.2(std,int,adv); C103.2 YES C402.2.3 Above/below grade Indicate material density category,wall weight and heat capacity for A5.2,A5.3,A8.0, C402.2.4 wall insulation qualifying mass walls; S4.1 C303.2.1 For qualifying ASTM C90 masonry walls,indicate loose-fill core insulation material and percentage of cores filled including grouted cores,bond beams,vertical fills,headers and any other grouted cores;