Laserfiche WebLink
I NOT USED <br />'I NOT USED <br />NOT USED <br />NOTES: <br />EXISTING #6 AWG STRANDED Cu <br />WIRES TO EXISTING EQUIPMENT <br />NEW CABINET, AMIA, ABTA,WG S ASIK,AN AND <br />ABIL GROUNDING KIT: i!G AWG STRANDED Cu <br />1. PROVIDE NO-OXBETE GREASE AT CONTACT <br />SURFACE BETWEEN LUG AND GROUND BAR401, <br />1 <br />WIRE WITH GREEN, 600V, THWN INSULATION <br />OR BLACK <br />-� <br />2. CONTRACTOR WILL VERIFY BUSS BAR <br />GROUNDING TO THE TOWER OR RING. <br />TYPE HS <br />TYPE 2-YA-2 <br />TYPE XA TYPE YA-2 TYPE GT <br />DUO <br />3. GROUND BARS AT BOTTOM OF TOWERS OR <br />MONOPOLES SHALL USE EXOTHERMIC <br />CONNECTION. <br />O 0 ,TO <br />0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 O <br />Do o000000000000000�0 <br />0 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 <br />O OO O O O O O O O O O O O O O O O r— <br />10 1 MAIN GROUND BAR <br />11 1 NOT USED <br />12 1 NOT USED <br />TWO-HOLE LUG, BOLTED TO <br />GROUND BAR USING 3/8" 16 x 1 <br />1/4"STAINLESS STEEL HEX UNIT <br />BOLTS AND HARDWARE. <br />WEATHERPROOFING <br />KIT (SEE NOTE 3) <br />ANTENNACABLE- <br />EXISTING MAIN GROUND BAR <br />TYPE TA <br />TYPE VN <br />TYPE NC <br />TYPE SS <br />TYPE GY <br />EXOTHERMIC WELD <br />TYPE VV <br />TYPE VS <br />TYPE VB <br />TYPE PT <br />TYPE GR <br />NOTE: <br />EXISTING (2) #2 AWG SOLID TINNED BARE Cu WIRE <br />TO EXISTING GROUND RING <br />ERICO EXOTHERMIC "MOLD TYPES' SHOWN HERE ARE EXAMPLES. CONSULT WITH <br />MANAGER FOR SPECIFIC MOLDS TO BE USED FOR THIS PROJECT. <br />PROJECT <br />CABLE GROUND KIT <br />#6 AWG STRANDED Cu WIRE WITH <br />GREEN, 600V,THWN INSULATION OR <br />BLACK (GROUNDED TO GROUND BAR) <br />ANTENNA AND/OR GPS CABLE <br />CONNECTION <br />CONNECTOR <br />NOTES: <br />1. DO NOT INSTALL CABLE GROUND KIT AT A BEND AND ALWAYS <br />DIRECT GROUND WIRE DOWN TO GROUND BAR. <br />2. GROUNDING KIT TYPE SHALL BE APPROVED BY TMO PRIOR TO INSTALLATION <br />3. WEATHERPROOFING SHALL INCORPORATE PPC WEATHERPROOFING <br />TAPE KIT, COLD SHRINK SHALL NOT BE USED. <br />8 1 CABLE GROUNDING <br />9 1 NOT USED <br />4 1 EXOTHERMIC WELDING <br />WIRE SIZE <br />BURNDY LUG <br />BOLT SIZE <br />#6 AWG GREEN INSULATED <br />YAOC-2TC38 <br />3/8'-18 NC S 2 BOLT <br />#2 AWG SOLID TINNED <br />YA3C-2TC38 <br />3/8" -10 NC S 2 BOLT <br />#2 AWG STRANDED <br />YA2C-2TC38 <br />3/8" -18 NC S 2 BOLT <br />#2/0 AWG STRANDED <br />YA28-2TC38 <br />--- 16 NC S 2 BOLT <br />#MO AWG STRANDED <br />YA28-2N <br />1/2" - i6 NC S 2 BOLT <br />.9VALC 1 <br />N.T.S. <br />NOTES: <br />1. ALL HARDWARE BOLTS, NUTS, <br />LOCK WASHERS SHALL BE <br />STAINLESS STEEL. ALL <br />HARDWARE ARE TO BE AS <br />FOLLOWS: BOLT, FLAT <br />WASHER, GROUND BAR, <br />GROUND LUG, FLAT WASHER. <br />LOCK WASHER AND NUT. <br />2. COPPER SHIELD, ANTIOX, CR <br />NOOX OR EQUIVALENT SHALL <br />BE PLACE WHERE ALL <br />DISSIMILAR METALS CONNECT. <br />3. ALL LUGS ARE TO BE <br />INSTALLED PER <br />HEAT SHRINK <br />MANUFACTURER'S <br />SPECIFICATIONS. <br />(CLEAR HEAT SHRINK INDOOR 8 <br />BLACK HEAT SHRINK OUTDOOR) <br />4. ALL LUGS MUST HAVE <br />BURNDY GROUND LUG <br />INSPECTION WINDOWS. <br />(SEE TABLE FOR SIZE <br />AND MODEL) <br />BURNDY GROUND LUG <br />NUT (TYP.) <br />(SEE TABLE FOR SIZE <br />LOCK WASHER <br />AND MODEL) <br />(TYP ) <br />BARE WIRE TO BE <br />FLAT WASHER <br />NO.OX AT BOTH ENDS <br />(NP.) <br />GROUNDING <br />CONDUCTOR <br />GROUND BAR <br />FLAT WASHER BOLT(TYP.) <br />(TYP.) <br />5 MECHANICAL LUG SCALE <br />N.T.S. 2 <br />NOTES: <br />1. PROVIDE NOOX GREASE AT CONTACT SURFACE BETWEEN LUG AND GROUND BAR <br />2. CONTRACTOR WILL VERIFY BUSS BAR GROUNDING TO THE TOWER OR RING. <br />3. GROUND BARS AT BOTTOM OF TOWERS OR MONOPOLES SHALL USE EXOTHERMIC <br />CONNECTION. <br />ANTENNA AND AHLOA GROUNDING KIT: <br />#6 AWG STRANDED Cu WIRE WITH <br />GREEN, 60OV,THWN INSULATION OR <br />BLACK <br />TWO -HOLE LUG, BOLTED <br />TO GROUND BAR USING <br />3/8%16 x 1 114" STAINLESS <br />STEEL HEX UNIT BOLTS <br />AND HARDWARE. <br />O Q Q Q O 0 0 0 0 O EXISTING 4"x12"xi/4' <br />O O O O O O O O Q O THK., TINNED <br />GROUND BAR ON <br />O O O O WALL, FLOOR OR ON <br />ANTENNA TOWER <br />0 0 0 0 O O O O r1 <br />6 1 SECTOR GROUND BAR <br />EXOTHERMIC WELD I <br />EXISTING #2 AWG SOLID TINNED <br />BARE Cu WIRE TO EXISTING TOWER <br />GROUND BAR OR MAIN GROUND BAR <br />3 <br />1L. HART <br />WAS,q �Y <br />�A <br />54777 <br />S��IVAL ��yCs <br />7.08.19 <br />IT IS A VIOIATION OF LAW FOR ANY PERSON, UNLESS THEY <br />ARE ACTING UNDER THE DIRECTION OF A LICENSED <br />PROFESSIONAL ENGINEER, TO ALTER THIS DOCUMENT. <br />T w-Mobile°• <br />19807 NORTH CREEK PARKWAY NORTH <br />BOTHELL, WA 98011 <br />Technologytftoclates <br />PNW MARKET OFFICE <br />650 SOUTH ORCAS STREET, STE. R-103 <br />SEATTLE, WA 98108 <br />Technologytftociates <br />ARCHITECTURE & ENGINEERING <br />2851 CAMINO DEL RIO SOUTH, STE. 200 <br />SAN DIEGO, CA 92108 <br />0 <br />OTN I. <br />ISSUED FOR 100%L800 CD <br />MGM <br />A <br />0SIDMI9 <br />ISSUED FOR L00090%CD <br />EDAM <br />REV <br />DATE <br />DESCRIPTION <br />BY <br />SE01845A <br />CASCADE HIGH <br />SCHOOL N. <br />WATER TANK <br />7410 OLYMPIC DRIVE <br />EVERETT, WA 98203 <br />WATERTANK <br />JURISD-N APPROVAL STAMP <br />DEPARTMENT FOR LAND USE <br />DEPARTMENT FOR BUttOWGBCONSTRUCTKNI <br />SHEET TITLE - <br />GROUNDING <br />DETAILS <br />SHEET NUMBER <br />G=2 <br />nIi3 <br />