7514 EVERGREEN WAY 2021-09-22 - Laserfiche WebLink

Lighting, Motor, and Liectrical Permit Checklist, Pg. 1 LTG-CHK 2015 Washington State Energy Code Compliance Forms for Commercial Buildings including R2,R3,R4 over 3 stories and all R1 Revised August 2016 Project Title: Wendy's Interior Dining Room/Toilet Room.Tenant Improvement Date 8/5/2018 The following information is necessary to check a permit application for compliance with the lighting,motor,and electrical requirements in the Washington State Energy Code,Commercial Provisions. Applicability Location in Building Department (yes,no,na) Code Section Component Compliance information required in permit documents Documents Notes LIGHTING CONTROLS Lighting controls, For all lighting fixtures,indicate lighting control method on C405.2 plans for spaces and lighting zone(s)served,or exception ni 2 general taken / Luminaire level Indicate on plans all fixtures provided with LLLC in lieu of fiC405.2 lighting controls C405.2 lighting controls;provide description of control (LLLC) capabilities and performance parameters For permanently installed lighting fixtures in dwelling units, C405.1 Lighting in dwelling indicate lighting control method on plans for spaces and units lighting zone(s)served,or demonstrate compliance with high efficacy exception C405.2.3 Indicate on plans the method of manual lighting control C405.2.1.1 (whether combined with occupancy sensor,automatic light ,�j C405.2.2.2 Manual controls reduction, daylight responsive or specific application controls), /4-/- II C405.2.4 location of manual control device and area or specifice C405.2.5 application it serves C405.2.2.1 Manual interior Indicate on plans which method of manual 50%lighting load Li C405.2.2.2 lighting controls C405.2.3 reduction is provided,or whether lighting load is reduced via f� occupancy sensors or daylight responsive Controls Indicate on plans the method of automatic shut-off control during unoccupied periods(occupancy sensor or time switch) Method of automatic for all lighting zones; �Y �' C405.2.2 shut-off control Indicate locations where automatic shutoff is provided by other methods(occupancy sensor or digital timer switch)or which time switch control exception applies Indicate on plans the spaces served by occupancy sensors; C405.2.1 Occupancy sensor Indicate whether occupancy sensor controls are configured to IA_ 11 C405.2.1.1 controls be manual-on,automatic 50%-on,or serve a space eligible for 077.. 2,- automatic 100%-on per exception Occupancy sensor Indicate aisleways and open areas in warehouse spaces A, - C405.2.1.2 controls- provided with occupancy sensor controls that reduce lighting warehouses power by 50% - C405.2.6 Digital timer switch Indicate required digital timer switch control!function when control is used • C405.2.2.1 Automatic time Indicate locations of override switches on plans and the lighting fflswitch controls zone(s)served,include area sq.ft. I Indicate primary and secondary sidelight daylight zone areas on plans,include sq.ft.; sal C405.2.4.2 Daylight zones- Indicate toplight daylight zone areas on plans,include sq.ft.; C405.2.4.3 Sidelight and toplight For small vertical fenestration assemblies(rough opening less than 10 percent of primary daylight zone)where daylight responsive controls are not required,provide fenestration area to daylight zone calculation(s) Indicate on plans lighting zone(s)served by daylight responsive controls; Identify sidelight and toplight daylight zones that are not provided with daylight sensing controls and the exception(s) II C405.2.4 Daylight responsive that apply; controls Indicate on plans the lighting load reduction Method- continuous dimming,or stepped dimming that provides at least two even steps between 0%-100%of rated power; Indicate that daylight sensing controls are configured to completely shut off all controlled lights in thelighting zone Additional controls- Identify spaces and lighting fixtures on plans that require II C405.2.5 Specific application lighting controls specific application lighting controls per this section Indicate on plans that display and accent ligltting,and display PAC405.2.5- Display and accent case lighting are controlled independently fron both general Items 1&2 lighting area lighting and other lighting applications within the same space; Indicate manual and automatic lighting control method