3721 OAKES AVE EVERETT SCHOOL DISTRICT 2021-11-15

2015 Washington State Encode Compliance Forms for Commercial,R2 and R3 over ries and all R1-Page 6 of 22 Mechanical Permit Plans Checklist MECH-CHK 2015 Washington State Energy Code Compliance Forms for Commercial Buildings including R2&R3 over 3 stories and all R1 Revised January 2017 Project Title: ESD-ATHLETICSBUILDING Date 5/28/2020 The following information is necessary to check a permit application for compliance with the mechanical systems and equipment requirements of the Washington State Energy Code,Commercial Provisions. Applicable Code Section Code Provision Information Required-Must be in permit documents Location in Building Department (yes no.nal Documents Notes NA C406.2.2 Minimum equipment To comply with additional efficiency package option,indicate that all listed heating and cooling C403.2.3 efficiency equipment have a rated efficiency that exceeds WSEC listed efficiency by at least 15% C406.2.3 To comply with additional efficiency package option,indicate rated FEG of stand alone fans is z NA C403.2.11.3 Minimum fan efficiency 71;indicate these fans are sized so the fan efficiency at design conditions is within 10%of the maximum total nr static efficiency HVAC System Controls Indicate locations of thermostatic and humidity control devices and the zones they serve on M0.2,0.3 plans,including perimeter system zones Where adjacent(neighboring)zones are controlled by separate thermostats(including perimeter systems used to offset heat gain or loss),and are connected by permanent openings Thermostatic controls >10%of either zone sf area,indicate controls configured to prevent adjacent zones from Yes C403.2.4.1 (thermostats and operating in conflicting modes(one in heat,other in cool);applies to adjacent perimeter zones, • humidistats) disc.rlf n nerirpetar Tunas ertd adiecant nari ¢ter and nonoerimeter 7npa app�ying xception 2 to nonpermeter zones adjacent to perimeter zones,--cote that setpoints and deadband settings in these zones are coordinated so cooling in a nonperimeter zone does not occur until the temperature in that zone is 5°F higher than the adjacent nerimeter 7nne temperature in heatinn NA C403.2.4.1.1 Heat pump supplementary Indicate staged heating operation with compression as the first stage of heating and heat supplemental heating controlled with outdoor lock-out temperature set to 40°F or less Yes C403.2.4.1.2 Deadband Indicate zone thermostatic controls configured with 5°F minimum deadband for systems that M0.2,0.3 control both heating and cooling If separate heating and cooling systems with separate thermostatic control devices are used to Setpoint overlap restriction serve a zone,indicate locations of both thermostatic control devices and the zone they serve Yes C403.2.4.1.3 (thermostats) on plans Indicate a limit switch,mechanical stop or DDC control with programming to prevent M0.2,0.3 simultaneous heating and cooling C403.2.4.2 Indicate zone thermostatic controls configured with required automatic setback and manual M0.2,0.3 Yes C403.2.4.2.1 Automatic setback and override functions,setback temperatures,and control method(automatic time clock or C403.2.4.2.2 shutdown nroarammable controls):note exceptions taken Yes C403.2.4.2.3 Automatic(optimum)start Indicate system controls that adjust equipment start time required to bring each area served up M0.2,0.3 to design temperature iust prior to scheduled occupancy NA C403.2.4.3 Outdoor supply air dampers Indicate automatic controls configured to close OSA damper during unoccupied equipment operation;not including economizer cooling,night flush or IMC required OSA/exhaust NA C403.2.4.3 Stairway and shaft vent Indicate method of activation of stairway and shaft vent dampers(fire alarm or interruption of dampers power) For systems serving areas>25,000 sf or spanning more than one floor,that include areas that NA C403.2.4.4 Zone isolation controls are expected to be occupied non-simultaneously;indicate controls that allow for independent space conditionina of isolation zones:or exception taken NA C403.2.12 Heating outside a building Indicate occupancy sensing or timer switch controls configured to automatically shut off heating system when area served is unoccupied NA C403.2.4.5 Snow melt systems Indicate automatic controls configured to shut off system when pavement temperature exceeds 50°F and no precipitation is falling,and when outdoor air temperature exceeds 40°F Yes C403.2.4.6 Freeze protection system Indicate automatic controls to shut off system when outdoor temperature exceeds 40°F,or M0.2,0.3 controls conditions protect fluid from freezing Group Rt hotel/motel For hotels and motels with over 50 guest rooms,indicate automatic controls serving guest NA C403.2.4.9 guest rooms rooms that are capable of setback(heating)and set-up(cooling)of temperature setpoint by at least 5°F:indicate control method-activated by room entry or occupancy sensor