Laserfiche WebLink
General Plumb�No�tes <br />1. All piping and plumbing per 2015 UPC. <br />2. Field verify all plumbing material/equipment locations and dimensions before proceeding with any work and report all discrepancies to the general <br />contractor. <br />3. These plans are schematic and do not indicate every offset required for routing. It shall be the P.C.'s responsibility to coordinate pipe routing and <br />elevations with other affected trades before construction. Where conflicts occur, rerouting may be necessary. <br />4. Coordinate plumbing installation with HVAC Mechanical, Fire Protection, and the Electrical Contractor. <br />5. Plumbing contractor to coordinate line voltage power connections with the E.G. for equipment within the plumbing contractors scope. <br />6. Field coordinate footing and floor sleeves where necessary <br />7. All pipe sizing noted on the drawings are minimum. <br />8. Provide cleanouts on sanitary sewer system as required by 2015 UPC. <br />9. All fire stopping of through and membrane penetration as required by the UPC shall be provided and installed by the P.C. <br />10. Slope Waste piping at 2% per foot minimum. Slope 4" waste piping at 1% per foot minimum <br />11. Pipe insulation to be provided on all hot water piping per the WSEC, as indicated in the Pipe Insulation Schedule below. Cold water piping <br />insulation to be minimum of 1/2" for condensation control. Traps and fixture piping below ADA lavatories shall be isolated with 1" insulation and <br />shields. <br />12. Hangers and supports shall be per MSS SP-69. Provide rigid insulation and shields at hanger locations. <br />13, G.C. to provide and install access panels where necessary for access to isolation valves, cleanouts and electronic fixture controllers. P.C. to <br />coordinate locations with G.C. <br />14. P.C. to provide accessible shutoffs for all domestic hot and cold water lines serving fixtures. <br />15. Provide and size vents per UPC. Combine vents and coordinate roof penetrations with G.C. prior to installation. All roof penetrations require <br />flashing. <br />16. All floor drains require trap primers unless otherwise noted. Size and install per industry Standards. <br />17. P.C. shall provide markup of deviations from contract dwgs for incorporation in as -built set on full size drawings. <br />18. P.C. shall provide full plumbing submittal package to Sunset Air for approval prior to purchase and installation. <br />19. Label all Piping and Direction of Flow. <br />20. P.C. shall install underground waste, water and drains to a point 5-feet past the building foundation. Connection to site underground utilities shall <br />be by others. <br />21. PIPING MATERIAL SCHEDULE: <br />22. <br />PIPING <br />LOCATION <br />MATERIAL <br />T JOINT <br />COLD WATER: <br />ALL <br />BELOW 2" - PEX / 2" AND ABOVE COPPER <br />NO -LEAD SOLDER <br />HOT WATER: <br />ALL <br />BELOW 2" - PEX / 2" AND ABOVE COPPER <br />NO -LEAD SOLDER <br />RAIN LEADERS: <br />ALL <br />PVC (CAST IRON IF IN PLENUM) E <br />OLVENT WELD CEMENT (HUBLES, <br />WASTE: <br />ABOVE GROUND <br />PVC (CAST IRON IF IN PLENUM) <br />OLVENT WELD CEMENT (HUBLES, <br />WASTE: <br />BELOW GROUND <br />PVC <br />SOLVENT WELD CEMENT <br />INDIRECT WASTE: <br />ALL <br />PVC <br />SOLVENT WELD CEMENT <br />VENT: <br />ALL <br />PVC <br />SOLVENT WELD CEMENT <br />GAS: <br />ALL <br />SCHEDULE 40 BLACK IRON <br />THREADED < 2-1/2" <br />PIPING INSULATION SCHEDULE:_ <br />PIPING <br />F TYPE <br />PIPE <br />SIZE <br />INSULATION <br />TYPE <br />MATERIAL <br />INSULATION <br />THICKNESS <br />UNDERSIDE OFROOFDRAINS: <br />OVERHEAD RAIN LEADERS: <br />ALL <br />ALL <br />FIBERGLASS <br />FIBERGLASS <br />ALL <br />ALL <br />112" <br />1/2" <br />VERTICAL RAIN LEADERS: <br />ALL <br />NOT REQUIRED <br />ALL <br />OVERHEAD COLD WATER: <br />ALL <br />FIBERGLASS <br />ALL (EXCEPT PEX)_ <br />1/2" <br />HOT WATER <br />1/2" - 1-112" <br />FIBERGLASS <br />ALL <br />ill <br />1-1/2"-4" <br />FIBERGLASS <br />ALL <br />1-1/2" <br />SYMBOL <br />DESCRIPTION <br />MANUFACTURER & MODEL NUMBERS <br />—FIN <br />TOILET: PROFLO: 1731WH <br />W <br />V <br />IN <br />r <br />CVV <br />IN <br />HW IN <br />GAS <br />IN <br />ELEC. <br />REMARKS <br />WATER CLOSET ADA <br />WC-1A <br />WALL MOUNT <br />SEAT: PROFLO: TSCOF2000WH <br />4" <br />2" <br />1/2" <br />ADA, VERIFY TOILET BOWL HANDLE SIDE BEFORE ORDERING <br />AUTO FV <br />FLUSH VALVE: SLOAN: 8111 <br />— <br />--- <br />-1/2-- <br />L-1 <br />LAV WALL -HUNG <br />SINGLE HANDLE <br />SINK: <br />tFAUCET: <br />_ECOS <br />PROFLO: 5414WH <br />SLOAN SF-2350-BDM 0.5 GPM <br />1 1/2" <br />1 1/2" <br />1/2" <br />" <br />S-1 <br />HAND WASH SINK <br />� STAINLESS <br />SINK: <br />FAUCET: <br />PROFLO: PFSR171963 <br />PROFLO: PFXC688OLSCP <br />1 1/2" <br />1 1/2" <br />1/2" <br />1/2" <br />- <br />DF-2 <br />DRINKING FOUNTAIN <br />� DOUBLE ADA A <br />TAIN: <br />FOUNTAIN: <br />ELKAY: LZSTL8WSLP TWO -LEVEL BARRIER FREE <br />2" <br />1 1/2" <br />1/2" <br />- <br />V <br />—L <br />W/ BOTTLE FILLER <br />__1/2"o CW <br />IF-1 <br />1 <br />1/2"o CW <br />A <br />1/2"o HW <br />PLUMBING 2ND FLOOR - DOMESTIC <br />WATER <br />1/8" = 11-01, <br />8 <br />6 7 <br />A <br />Zfl <br />0 K Vid? <br />210-i tit <br />11" <br />PLUMBING 2ND FLOOR - WASTE AND <br />VENT - ABOVE FLOOR <br />1/8" = 1 1-011 <br />iJ <br />31. 0 <br />2' <br />UP TO 2ND FLOOR T.I. 1 <br />CONNECT DOWN TO <br />EXISTING WASTE <br />UP TO 2ND FLOOR T.I. <br />PLUMBING 2ND FLOOR - WASTE AND <br />VENT BELOW FLOOR <br />1/8" 011 <br />0 ywlaw4 <br />Lu <br />0 <br />Q <br />rr. <br />0 <br />ILL <br />Z <br />V) <br />Ln< <br />>: <br />LU <br />Ci <br />no <br />0 <br />ALL DOCUMENTS, ELECTRONIC OR OTHERWISE, <br />PREPARED BY SUNSETAIR ARE FOR USE SOLELY <br />WITH RESPECT TO THE SUBJECT PROJECT. SUNSET <br />AIR IS THE OWNER OF THE DOCUMENTS, AND SHALL <br />RETAIN ALL COMMON LAW, STATUTORY, AND OTHER <br />RESERVE RIGHTS, INCLUDING COPYRIGHTS. <br />EXPRESSLY CONDITIONED UPON SUNSET AIR <br />PERFORMING THE CONSTRUCTION ASSOCIATED <br />WITH THE DOCUMENTS FOR THE PROJECT, SUNSET <br />AIR GRANTS TO CLIENT A NON-EXCLUSIVE LICENSE <br />TO REPRODUCE SUNSETAIRS DOCUMENTS SOLELY <br />FOR PURPOSES OF CONSTRUCTING, USING, AND <br />MAINTAINING THE PROJECT, PROVIDED THAT CLIENT <br />SHALL COMPLY W ITH ALL OBLIGATIONS, INCLUDING <br />EXPIRES: 08-11-16 <br />LM <br />Uj <br />Lu <br /><< <br />>- <br />03 <br />0 1­— <br />(j LJj <br />UjC:) <br />ry C-) <br />Lu(�D <br />�:> " <br />r,— <br />C 00 <br />Jr- LU o-) <br />DESIGNEDBY: <br />RMC <br />DRAWN BY: <br />SFC <br />REVIEWED BY: <br />RJP <br />REVISIONS <br />07.18.18 <br />ISSUE FOR DESIGN <br />DEVELOPMENT <br />09.10.18 <br />90% CD <br />09.20.18 <br />PERMIT SET <br />PLUMBING GENERAL <br />NOTES, SCHEDULES, AND <br />FLOORPLANS <br />-SHEET NUMBER <br />