910 SE EVERETT MALL WAY 2022 PEARLE VISION Plans 2023-01-09

GENERAL DEMOLITION NOTES - - 1. IN EVERY INSTANCE OF DEMOLITION AND/OR REMODELING, THE E.C. SHALL 10. ALL WALLS, CEILINGS, FLOORS, ETC., BEING DISTURBED BY THE WORK SHALL FIGURE A COMPLETE JOB AS NONE OTHER SHALL BE ACCEPTED. BE RETURNED TO FINISHED CONDITIONS TO MATCH EXISTING BY THE E.C. & HE SHALL DO HIS OWN CUTTING &. PATCHING AS NECESSARY UNDER HIS 2. THE DRAWINGS ARE TO BE USED ONLY AS A GUIDELINE FOR DEMOLITION. CONTRACT. THE E.C. MUST VISIT THE SITE PRIOR TO BIDDING TO VERIFY ALL WORK REQUIRED FOR A COMPLETE JOB & INCLUDE THE COST OF SUCH WORK IN HIS 11. EXISTING MATERIALS SHALL BE TURNED OVER TO THE OWNER. IF NOT BID. REQUIRED BY OWNER, THE E.C. SHALL REMOVE THESE MATERIALS FROM THE PREMISES. 3. THE E.C. SHALL MAINTAIN EXISTING SERVICES TO & IN THE EXISTING AREA AS REQUIRED. 4. IF NECESSARY, THE E.C. SHALL PROVIDE TEMPORARY SERVICES IN THE EXISTING AREAS. 5. THE E.C. SHALL DISCONNECT & REMOVE ELECTRIC SERVICE TO ALL MECHANICAL EQUIPMENT BEING REMOVED AS A RESULT OF THE REMODELING. 6. ELECTRICAL EQUIPMENT & DEVICES SHALL BE REMOVED COMPLETE INCLUDING CONDUIT & WIRE. 7. FLUSH MOUNTED WALL OUTLETS SHALL BE REMOVED AND THE WALL PATCHED AND FINISHED TO MATCH THE ADJACENT WALL FINISHES. AND/OR8. ANY EXISTING CONDUIT, WIRING ELECTRICAL MECHANICAL DEVICES BEING DISTURBED BY THE WORK SHALL . REWORKED BY CONTRACTORAS • ITS FORMER EXISTING OPERATING CONDITION. 9. ANY CIRCUITS FEEDING THROUGH DEVICES OR EQUIPMENT BEING RELOCATED, REWORKED, OR ABANDONED & SERVING OTHER ELECTRICAL DEVICES, AND/OR EQUIPMENT SHALL BE MAINTAINED BY PROVIDING J-BOXES OR OTHER ACCEPTABLE METHOD AS REQUIRED. 12. NO CONDUIT, BOXES, WIRING, OR CABLES SHALL BE INSTALLED WITHIN 1 1/2" OF THE LOWEST POINT OF THE UNDERSIDE OF THE ROOF DECKING, NOR SHALL THEY BE INSTALLED CONCEALED WITHIN METAL -CORRUGATED ROOF DECKING, THE E.C. SHALL BE RESPONSIBLE TO REPLACE AND/OR REWORK EXISTING CONDUIT, BOXES, WIRING, AND CABLING THAT IS NOT IN COMPLIANCE WITH THIS REQUIREMENT. 13. ALL CONDUIT AND CABLING SHALL BE PROPERLY SUPPORTED AS REQUIRED BY THE NATIONAL ELECTRICAL CODE. THE E.C. SHALL BE RESPONSIBLE TO REPLACE AND/OR REWORK EXISTING CONDUIT AND/OR CABLING THAT IS NOT IN COMPLIANCE WITH THIS REQUIREMENT. i4. E.C. SHALL FIELD VERIFY SLAB ON GRADE FLOOR CONSTRUCTION TYPE PRIOR TO CUTTING. UNDER NO CIRCUMSTANCES SHALL THE CONTRACTOR CUT A STRUCTURAL FLOOR SLAB THICKER THAN FOUR (4") INCHES WITHOUT PRIOR WRITTEN APPROVAL FROM ENGINEER OF RECORD. NOTIFY ENGINEER OF RECORD OF ANY SLAB THICKNESS GREATER THAN FOUR (4") INCHES PRIOR TO PROCEEDING WITH ANY SAW CUTTING. REFER TO SHEET S001 FOR MORE INFORMATION. KEY NOTES - ELECTRICAL DEMOLITION 1. EXISTING PANELBOARD AND ASSOCIATED ELECTRICAL DEVICES TO REMAIN. 2. DISCONNECT AND REMOVE ALL EXISTING LIGHT FIXTURES - INCLUDING EXIT AND EMERGENCY FIXTURES. 3. DISCONNECT AND REMOVE ALL ELECTRICAL DEVICES - INCLUDING SWITCHES, RECEPTACLES, DATA ETC. 4. DISCONNECT AND REMOVE EXISTING PHONE BOARD. SALVAGE ANY EXISTING EQUIPMENT TO BE RELOCATED TO NEW PHONE BOARD LOCATION. ELECTRICAL - DEMOLITION SCALE: 1/4" = 1'-D" INFORMATION IS BASED ON SURVEY PICTURES. VERIFY ALL WORK IN FIELD. ADVISE NEX I ORE PROJECT MANAGER OF ANY DISCREPANCIES. Construction for: Revisions: Mark Date ELECTRICAL