4523 RIVERFRONT BLVD 2023-01-18 - Laserfiche WebLink

_XI F_ Ox LL] J Q 0 iiiiiiiiiiiiii (Y D J M Q 00 F O V D O u7 U*) SYSTEM INFO (11)Q CELLS Q.PEAK DUO BLK ML-G10+ 400W (11)ENPHASE IQ8PLUS-72-2-US 240V DC SYSTEM SIZE:4.40 kWDC 1 I 1 1 AC SYSTEM SIZE:3.30 kWAC ■;; ; SM SOLAR APPENDIX C ; ■ ■;; ; S MSOLAR CODE COMPLIANCE NOTES � REVISIONS •• MOUNT UNIVERSALAP ENDCLAMP INSTALLATION GUIDE ; PAGE an 1. MOUNT INSTALLATION GUIDE PAGE DESCRIPTION DATE REV SYSTEM LEVEL FIRE CLASSIFICATION The system fire class rating requires installation in the manner specified in the SOLARMOUNT Installation Guide.SOLARMOUNT has been classified to the system WN e Level fire portion of UL2703. SOLARMOUNT has achieved system Level performance for steep sloped roofs.System level fire performance is inherent in the SOLARMOUNT design,and no additional mitigation measures are required.The fire classification rating is only valid on roof pitches greater than 2:12(slopes>2 Signature with Seal inches per foot,or 9.5 degrees). The system is to be mounted over fire resistant roof covering rated for the application.There is no required minimum or maximum • height limitation above the roof deck to maintain the system fire rating for SOLARMOUNT.Module Types&System Level Fire Ratings are listed below: �-© Rail type Module Fire TySystem Level fire Rating Rail Direction Module Mitigation Orientation Required 3N WN pes Standard Rail 1,2,3 w metal frame.10 w metal Class A,Class B&Class C East-West Landscape OR Portrait None Required frame,19,22,25,29,&30 North-South Landscape OR Portrait None Required Light Rail 1&2 ___FClass A.Class B&Class C East-West Landscape OR Portrait None Required 1.Position clamp to align T-bolt with rail 2.Rotate clamp clockwise 2/3 of a turn 3.Place module at Least 3/4-from end of 4.While applying pressure to hold the East-West Landscape OR Portrait None Required �] PROJECT NAME&ADDRESS slot.Lower clamp and Insert T-bolt into to engage T-bots inside rail slot, rail and position clamp against module clamp against the module,push down on fail slat. frame, the module side of the clamp cap. This pirkiny system may he used In yround and/or mount a PV mrrdute tnmplyinq with UL 1703 or UL617SO only wtren the spr_ific module has ham+, "7 in compilante with the Inctude-d insLructlorn. UL2703 CERTIFICATION MARKING LABEL UNIRAC 0 Unirac SOLARMOUNT is listed to UL 2703.Certification marking is embossed on all mid clamps as shown. J w O -----• Labels with additional information will be provided.After the racking system is fully assembled,a single CIO . O Imo'• — } label should be applied to the SOLARMOUNT rail at the edge of the array.Before applying the label,the Cfl /""' j —! 4 corners of the label that do not pertain to the system being installed must be removed so that only the C US w m C 7 installed system type is showing. 26G909 w f'V O - - 1 so Tm s:a ss Tm ss mm w z OO O U = z O CD 00 U W of Q I- U) 0 - U) 0 ILL3� 00 SI rrwq •O mm K� � r - U) U) W\ o Uj 5.When the cap contacts the module 6.Tighten bolt and torque to 1S h-lbs. 7.Confirm clamp is engaged in correct module height position and that the top of the R_ / frame,release and it will re-engage to cap is sitting level with the module frame. �/ w Z the clamp base. r1/ NOTE:When installing 46mm modules,loosen bolt by 1 turn before positioning clamp • e�!u.u.c - • • (y.) 0l, a- against module frame.Do not force clamp onto module frame as this may damage the �: _ - N LIJ Q 9 ondin pin _ •—' -- SM STANDARD RAIL / 5M LIG ITRAIL r e� r'/ w DATE:6/23/2022 SHEET NAME EQUIPMENT SPECIFICATION SHEET SIZE ANSI B 11" X 17" SHEET NUMBER PV-15