2509 LEONARD DR 2023-04-28 - Laserfiche WebLink

Lumio SMART ENERGY TODAY (SET) 1550 DIGITAL DR,LEHI,UT 84043,USA SYSTEM INFO (20)Q CELLS Q.PEAK DUO BLK ML-G10+ (400W) (20)ENPHASE IQ8PLUS-72-2-US(240V) DC SYSTEM SIZE:8.000 kWDC ■■ ' SM SOLAR APPENDIX C ■■ SOLAR CODE COMPLIANCE NOTES : E AC SYSTEMSIZE:6000kWAC as■ MOUNT UNIVERSAL�AP�ENDCLAMP INSTALLATION PAGE ��■ MOUNT INSTALLATION PAGE ---------------------------------------------------------------------------------------------------------------------------GUIDE--:-------- -------- --------------------------------------------------------------------------------------------------------------------------GUIDE-:-------- - -------- SYSTEM LEVEL FIRE CLASSIFICATION REVISIONS The system fire class rating requires installation in the manner specified in the SOLARMOUNT Installation Guide.SOLARMOUNT has been classified to the system DESCRIPTION DATE REV ® level fire portion of UL2703. SOLARMOUNT has achieved system level performance for steep sloped roofs.The fire classification rating is only valid on roof pitches greater than 2:12(slopes 3 2 inches per foot,or 9.5 degrees). The system is to be mounted over fire resistant roof covering rated for the application.There is no required minimum or maximum height limitation above the roof deck to maintain the system fire rating for SOLARMOUNT.Module Types,System Level Fire Ratings, _ and Mitigation Requirements are listed below: E— RaRType Module Fir*lypes System laid Fire Rating Rall Direction Module Mitigation ONantatfort I Required Standard&HD Raps 1,2,3 with Metal Frame,10 with Metal Class A.Class B&Class C East-West Landscape OR Portrait None Required PROJECT NAME&ADDRESS sa-MIN Frame,l9,22,25,29,&30 — - — North-South Landscape OR Portrait None Required - Light Rall 1&2 Class A,Class B&Class C East-West Landscape OR Portrait None Required Q North-South Landscape OR Portrait None Required fn 1.Position clamp to align T-bolt with rail 2.Rotate clamp clockwise 2/3 of a turn S.Place module at least 3/4'from end of 4.While applying pressure to hold the slot.Lower clamp and Insert T-bolt into to engage T-bolt inside rail slot, rail and position clamp against module clamp against the module,push down on Standard.Light.& 4&S t.lassA.Ctass8&Class C East-West Landscape OR Portrait Trim Installation Per Solar rail slot Game the module side of the clamp cap. HD Rafts North-South Landscape OR Portrait Mount Installation Guide - - - O This racking Wstem mdf be used to ground andror mourn a P"i mooule eompiying with LILL703 or UL61730 Dnly wizen rhe specific module iias reen errwaiEa ter N grounning and/or mouunny in rumpllanct wilts Lir Inth~1 instructions. 00 UNIRAC CY) UL2703 CERTIFICATION MARKING LABEL Q CD Unirac SOL.ARMOUNT is listed to UL 2703.Certification marking is embossed on all mid clamps as shown.Labels with w O additional information will be provided.After the racking system is fully assembled,a single Label should be applied to the S�.a �It LL] O r , SOLARMOUNT rail at the edge of the array.Before applying the Label,the comers of the label that do not pertain to the �I O % T I r system being installed must be removed so that only the installed system type is showing. C US r\ O r 50 mm 57&11 mn 55 mm NiliE�inv c:WCOiAruuW��.PwCee:WOO 9W..r•i5 vitibie,bW not outwalo(at�.��, 7.66909 = vW � LIj � ; L0? Z W L0 W 00 to mm Mmm as mm io U W - Z p S.When the cap contacts the module 6.Tighten bolt and torque to 15 ft-lbs, 7.Confirm clamp is engaged in correct module height position and that the top of the > frame,release and it will re-engage to cap is sitting level with the module frame. Q Q the clamp base. Z NOTE:When installing 46mm modules,loosen bolt by 1 turn before positioning clamp a a a!linear _— _ a a a ymy� O against module frame.Do not force clamp onto module frame as this may damage the `� —— bonding pin, y��.;_ �� W SM STANDARD RAIL _"""� ��'/ SM LIGHT RAIL J - CA O LO N DATE: 10/28/2022 SHEET NAME EQUIPMENT SPECIFICATIONS SHEET SIZE ANSI B 11" X 17" SHEET NUMBER PV-18