Laserfiche WebLink
Lumio <br /> SMART ENERGY TODAY <br /> (SET) <br /> 1550 DIGITAL DR,LEHI,UT <br /> 84043,USA <br /> SYSTEM INFO <br /> (20)Q CELLS <br /> Q.PEAK DUO BLK ML-G10+ <br /> (40OW) <br /> (20)ENPHASE <br /> I08PLUS-72-2-US(240V) <br /> DC SYSTEM SIZE:8.000 kWDC <br /> SM■■ : SOLAR STANDARD SYSTEM GROUNDING ' ■ �• SOLAR APPENDIX C ■ 4C SYSTEM SIZE:6.000 kWAC <br /> on■ MOUNT INSTALLATION GUIDE PACE an MOUNT UNIVERSALAF MIDCLAMP INSTALLATION GUIDE : PACE <br /> --------------------------------------------------------------------------------------------------------------------------------------------- --------------------------------------------------------------------------------------------------------------------------------------------- <br /> REVISIONS <br /> WEEBLUs DESCRIPTION DATE REV <br /> ----------- <br /> -__-_— ,Single Use Only I„„ <br /> i <br /> PROJECT NAME&ADDRESS <br /> ONLY ONE LUG PER ROW OF MODULES: % ee <br /> Only one lug per row of modules is r <br /> WEEBLUGCONDUCfOR-UNIRAC P/N 0080025: <br /> required. See Page F for additional lugs �— _ �� Apply Anti Seize and insert a bolt in the aluminum rail and through the clearance hole U) <br /> required for expansion joints. = in the stainless steel flat washer. Place the stainless steel flat washer on the bolt, <br /> oriented so the dimples will contact the aluminum rail Place the lug portion on the 1.Position clamp to align T bolt with rail 2.Rotate damp clockwise 2/3 of a tum 3.Slide clamp into position against 4.Place second module. <br /> bolt and stainless steel flat washer.Install stainless steel flat washer,lock washer and slot.Lower clamp and insertT-bolt into to engage T-bolt inside rail slot. module. 1 <br /> nut.Tighten the nut until the dimples are completely embedded into the rail and lug. rail slot O <br /> TORQUE VALUE 10 It los.(See Note on PG.a1 00 <br /> See product data sheet for more detaiLc,Modet No.WEEB-LUG•6., O <br /> Cf7 <br /> Q <br /> GROUNDING LUG MOUNTING DETAILS: O <br /> Star Wasna Ie O <br /> Details are provided for both the WEEB and Ilsco products.The WEEBLug has a slnylM <br /> e use Only �-> LLI O <br /> grounding symbol located on the lug assembly.The Ilsco lug has a green colored � Vi CO W I-_ 00 <br /> set screw for grounding indication purposes.Installation must be in accordance ' O <br /> lopwith NFPA NEC 70,however the electrical designer of record should refer to the - Aq: = U O <br /> latest revision of NEC for actual grounding conductor cable size. TtaMIMAtToep n L J U Z W <br /> i - I.o..11 canduam r W LO <br /> Reyuurd II not using approved uttegrated grounding uuaunrvetels 0 > <br /> "."pm W the tolr:, Z Ln <br /> W <br /> +-4 AWG:SSin(I•-. LU (/) 0 <br /> AWG 25"'A, U <br /> GROUNDING LUG-BOLT SIZE&DRILL SIZE Z W' 0 <br /> 0 <br /> GROUND LUG BOLT SIZE DRILL SIZE Z <br /> ILSCO LAY-IN LUGODNDUCTbIt-UNIRAC P/N 008009P:Alternate Grounding Lug > 0 Z <br /> WEEBLug 1/4- WA-Place in Top SM hall Slot Drill,deburr hole and bolt thru both rail walls per table. S.Tighten bolt and torque to 15 ft-lbs. NOTE:If excessive force is applied in 0— <br /> ASCO Lug x10-32 7/32' TORQUE VALUE S R lbs.(See Not, step 2,the cap may over-rotate causing Q Q <br /> See ILSCO product data sheet for more details,Model No.GBL-4DIIL it to be mis-aligned with the module Z <br /> Torque value depends on conductor size. frame.If this occurs,keep rotating the O <br /> See product data sheet for torque value. cap clockwise until it returns to the W <br /> NOTE:ISOLATE COPPER FROM ALUMINUM CONTACT TO PREVENT CORROSION original position. J <br /> M <br /> O <br /> Lf� <br /> N <br /> DATE: 10/28/2022 <br /> SHEET NAME <br /> EQUIPMENT <br /> LSPECIFICATIONS <br /> SHEET SIZE <br /> ANSI B <br /> 11° X 17" <br /> SHEET NUMBER <br /> PV-20 <br />