2509 LEONARD DR 2023-04-28 - Laserfiche WebLink

Lumio SMART ENERGY TODAY (SET) 1550 DIGITAL DR,LEHI,UT 84043,USA SYSTEM INFO (20)Q CELLS Q.PEAK DUO BLK ML-G10+ (40OW) (20)ENPHASE IQ8PLUS-72-2-US(240V) DC SYSTEM SIZE:8.000 kWDC ■ENISM SOLAR APPENDIX C I ■ ■;; SOLAR CODE COMPLIANCE NOTES I ■ 4C SYSTEM SIZE:6.000 kWAC ■■ MOUNT UNIVERSAL�AF ENDCLAMP INSTALLATION GUIDE PAGE ■■ MOUNT INSTALLATION GUIDE ; - -------------------------------------------------------------------------------------------------------------------------------------------- --------------------------------------------------------------------------------------------------------------------------------------------- PAGE SYSTEM LEVEL FIRE CLASSIFICATION REVISIONS The system fire class rating requires instaLLation in the manner specified in the SOLARMOUNT InstaLLation Guide.SOLARMOUNT has been classified to the system DESCRIPTION DATE REV 0 level fire portion of UL2703. SOLARMOUNT has achieved system level performance for steep sLoped roofs.The fire classification rating is only vaLid on roof pitches REVISION 1 01/21/2023 A greater than 2:12(slopes 3 2 inches per foot,or 9.5 degrees). The system is to be mounted over fire resistant roof covering rated for the appLication.There is no required minimum or maximum height Limitation above the roof deck to maintain the system fire rating for SOLARMOUNT.Module Types,System Level Fire Ratings, _ and Mitigation Requirements are listed below: Rail Type Module Fire Types System Level Fre Rating Rail Direction Module Mitigation Orientation Required Standard&HD Rails 1,2,3 with Metal Frame,10 with Metal CLass A,Class B&Class C East-West Landscape OR Portrait None Required PROJECT NAME&ADDRESS 3/4'141N. Frame,19,22,25,29,&30 North-South Landscape OR Portrait None Required LOP Light Rail 1&2 CLass A,Class B&Class C I East-West Landscape OR Portrait None Required Q North-South I Landscape OR Portrait None Required (n 1.Position clamp to align T-bolt with rail 2.Rotate clamp clockwise 2/3 of a turn 3.Place module at least 3/4"from end of 4.WhiLe applying pressure to hold the slot.Lower clamp and Insert T-bolt into to engage T-bolt inside rail slot. rail and position clamp against module clamp against the module,push down on Standard,Light,& 4&5 Class A,Class B&Class C East-West Landscape OR Portrait Trim installation per Solar rail slot. frame. the module side of the clamp cap. HD Rails North-South Landscape OR Portrait Mount Installation Guide � O This racking system may be used to ground and/or mount a PV module complying with UL1703 or UL61730 onlywhen the specific module has been evaluated for N grounding and/or mounting in compliance with the included instructions. O UNIRAC UL2703 CERTIFICATION MARKING LABEL Q O Unirac SOLARMOUNT is listed to UL 2703.Certification marking is embossed on all mid clamps as shown.Labels with > O additional information will be provided.After the racking system is fully assembled,a single Label should be applied to the ® UJ > MO SOLARMOUNT rail at the edge of the array.Before applying the Label the corners of the label that do not pertain to the U) LU LL; _' system being installed must be removed so that only the installed system type is showing. CIO:US = U W 00 3o mm 32 8 33 mm 33 mm Note:The sticker label should be placed such that it is visible,but not outward facing. 266909 z QW LO LU Cf) LU O U w O 38 mm 10 mm 46 mm z 5.When the cap contacts the module 6.Tighten bolt and torque to 15 ft-lbs. 7.Confirm clamp is engaged in correct module height position and that the top of the > d frame,release and it will re-engage to cap is sitting Level with the module frame. Q Q the clamp base. NOTE:When installing 46mm modules,loosen bolt by 1 turn before positioning clampO w M\ �\ O against module frame.Do not force clamp onto module frame as this may damage the _s �� " " bonding pin. q=ty w s "�,.'Te:.�. LLI SM STANDARD RAIL SM LIGHT RAIL _j O Lf) N DATE: 1/21/2023 F SHEET NAME EQUIPMENT LSPECIFICATIONS SHEET SIZE ANSI B 11rr X 17" SHEET NUMBER PV-18