Laserfiche WebLink
Lumio <br /> SMART ENERGY TODAY <br /> (SET) <br /> 1550 DIGITAL DR,LEHI,UT <br /> 84043,USA <br /> SYSTEM INFO <br /> (20)Q CELLS <br /> Q.PEAK DUO BLK ML-G10+ <br /> (40OW) <br /> (20)ENPHASE <br /> IQ8PLUS-72-2-US(240V) <br /> DC SYSTEM SIZE:8.000 kWDC <br /> ■■ ; SOLAR STANDARD SYSTEM GROUNDING ■ �;; SOLAR APPENDIX C :: N AC SYSTEM SIZE:6.000kWAC <br /> Nom■ ; MOUNT INSTALLATION GUIDE--:-PAGE 1■ MOUNT F� ; PAGE <br /> ---------------------------------------------------------------------------------------------------------------------------------- -------- -----------------------------------------------------------------------UNIVERSA�------------,A------MIDCLAMP----------------INSTALLATION------------------GUIDE------------------ <br /> REVISIONS <br /> WEEBLUG TERMINALTORQUE, <br /> Single Use Only 40 Install conductor and DESCRIPTIONDATE REV <br /> -- �_..... torque to the followin. <br /> 6-14 AWG:5ft-I REVISION 01/2112023 A <br /> d <br /> =fie <br /> PROJECT NAME&ADDRESS <br /> ONLY ONE LUG PER ROW OF MODUL <br /> Only one Lug per row of modules is WEEBLUG CONDUCTOR-UNIRAC P/N 008002S: Q <br /> required. See Page F for additional tugs _�� AppLyAnti Seize and insert a bolt in the aluminum rail and through the clearance hole f) <br /> required for expansion joints. <br /> in the stainless steel flat washer. Place the stainless steel flat washer on the bolt, <br /> oriented so the dimples will contact the aluminum rail Place the lug portion on the 1.Position clamp to align T-bolt with rail 2.Rotate clamp clockwise 2/3 of a turn 3.Slide clamp into position against 4.Place second module. <br /> bolt and stainless steel flat washer.Install stainless steel flat washer,Lock washer and slot.Lower clamp and insert T-bolt into to engage T-bolt inside rail slot. module. <br /> nut.Tighten the nut until the dimples are completely embedded into the rail and Lug. rail slot O <br /> CN <br /> TORQUE VALUE 10 ft lbs.(See Note on PG.A) 000 <br /> - - - See product data sheet for more details,Model No.WEEB-LUG-6.7 O O <br /> GROUNDING LUG MOUNTING DETAILS: Star Washer is O <br /> � O <br /> Details are provided for both the WEEB and Ilsco products.The WEEBLug has a Single use Only LU CY)O <br /> grounding symbol located on the lug assembly.The Ilsco lug has a green colored In C) <br /> set screw for grounding indication purposes.Installation must be in accordance �-_ Q LL] O <br /> with NFPA NEC 70,however the electrical designer of record should refer to the = 0 UJ O <br /> (-)Latest revision of NEC for actual grounding conductor cable size. O TERMINALTORQUE, W W <br /> Required if not using approved integrated grounding microinvetersInstall Conductor and 0 > <br /> torque to the following: z 1.0 <br /> 4-6 AWG:35in-lbs LLI (n LIJ O <br /> a AWG:25 in-lbs U LL] ck� CD <br /> 10-14 AWG:20 in-lbs z � 0 <br /> GROUND LUG BOLT SIZE DRILLSIZE <br /> ILSCO LAY-IN LUG CONDUCTOR-UNIRAC P/N 00800913:Alternate Grounding Lug > 0 z <br /> WEEBLug 1/4' N/A-place in Top SM Rail Slot -Drill,deburr hole and bolt thru both rail watts per table. 5.Tighten bolt and torque to 15 ft-lbs. NOTE:If excessive force is applied in 0 <br /> IISCO Lug u10-32 7/32- TORQUE VALUE 5 ft lbs.(See Note on PG.A) step 2,the cap may over-rotate causing Q Q <br /> See ILSCO product data sheet for more details,Model No.GBL-4DBT. it to be mis-aligned with the module z <br /> Torque value depends on conductor size. frame.If this occurs,keep rotating the O <br /> See product data sheet for torque value. cap clockwise until it returns to the ILj <br /> NOTE:ISOLATE COPPER FROM ALUMINUM CONTACT TO PREVENT CORROSION original position. J <br /> O') <br /> O <br /> N <br /> DATE: 1/21/2023 <br /> F SHEET NAME <br /> EQUIPMENT <br /> LSPECIFICATIONS <br /> SHEET SIZE <br /> ANSI B <br /> 11tt X 17" <br /> SHEET NUMBER <br /> PV-20 <br />