2721 WETMORE AVE MARQUEE APARTMENTS 2023-06-28

/$ Building Permit Plans Checklist, pg. 2 ENV-CHK 2015 WSEC Compliance Forms for Commercial Buildings including R2,R3,&R4 over 3 stories and all R1 Revised Oct 2017 Project Title: MarqueeDate Apartments 03/14/2019 Applicability Code Location in Building (yes,no,na) Section Component Compliance information required in permit documents Documents Department Notes C103.2 Indicate rated U-factor(swinging)or R-value(non-swinging-roll- C402.4.4 Opaque doors up/sliding)on wall sections or in door schedules-applies to doors with less than 50%glazed area Floor over outdoor or Indicate R-value(s)of cavity/continuous insulation on floor sections; C402.2.5 unconditioned space Indicate framing material on floor sections; insulation Indicate material density category and weight of qualifying mass floors Indicate R-value of continuous insulation on wall section or foundation detail; C402.2.6 Slab-on-grade floor Indicate insulation extends down vertically and/or horizontally the required C303.2.1 insulation distance from top of slab; Indicate method of protection of exposed exterior slab edge insulation Indicate R-value of continuous insulation on wall section or foundation Radiantly heated detail; C402.2.6 slab-on-grade floor Indicate insulation extends down vertically from top of slab and then C303.2.1 insulation horizontally under the entire slab; Indicate method of protection of exposed exterior slab edge insulation Radiant heating Indicate insulation R-value behind radiant panels,U-bend/headers and C402.2.8 system insulation bottom surface of radiantly heated floors(other than radiantly heated slab- on-grade) C402.4.1 Vertical fenestration Provide calculation for total vertical fenestration area as a percentage of C502.2.1 gross above grade wall area(WWR)for new construction,additions and C503.3.2 maximum area alterations in ENV-SUM Provide calculations showing that the percentage of overall conditioned floor area within daylight zones is equal to or greater than 50%in 1 and 2 story buildings;OR Provide calculations showing that the percentage of overall net floor area Increased within daylight zones is equal to or greater than 25%in buildings 3 stories C402.4.1.1 prescriptive or more;include the gross floor area and list of spaces omitted for the net C405.2.4.1 maximum vertical floor area; C502.2.1 fenestration area C503.3.2 with daylight zones Note in envelope plans that all lighting fixtures located within daylight and controls zones shall be provided with daylight responsive controls per WSEC Section C405.2.4.1;indicate method of control in lighting fixture schedules Indicate that the VT of vertical fenestration is at least 1.1 times the rated SHGC Increased Indicate high performance U-factors and SHGC values in fenestration C402.4.1.3 prescriptive schedules; C502.2.1 maximum vertical Indicate if an area-weighted U-factor is used for multiple fenestration C503.3.2 fenestration area elements within the same fenestration category per Table C402.3;provide with high- U-factor calculations • Increased prescriptive Indicate that for eligibility,all occupied,conditioned spaces will be served C402.4.1.4 maximum vertical by a dedicated outside air system(DOAS)that delivers ventilation air C403.6 fenestration area without requiring operation of the heating/cooling system per Section with DOAS C403.6 mechanical systems Wall/vertical Indicate if component performance with target area adjustment will be C402.1.5 fenestration target used to account for vertical fenestration area in excess of the prescriptive area adjustment maximum allowed C402.4.1 Skylight maximum Provide calculation for total skylight area as a percentage of gross roof C502.2.2 area area(SRR)for new construction,additions and alterations in ENV-SUM C503.3.3 Roof/skylight target Indicate if component performance with target area adjustment will be C402.1.5.2 area adjustment used to account for skylight area in excess of the prescriptive maximum allowed Indicate U-factors,SHGC and VT values in fenestration schedules; U-factors,SHGC Indicate if an area-weighted U-factor is used for multiple fenestration C402.4.3 and VT for all elements within the same fenestration category per Table C402.3;provide C303.1.3 fenestration U-factor calculations assemblies Indicate if values are NFRC or default;if default then specify frame type, glazing layers,gap width.low-e coatings.gas-fill Permanent shading For windows with overhangs or permanent projection shading devices, C402.4.3 provide projection factor calculations(Equation C4-6)and associated devices minimum SHGC for north and non-north orientations