Laserfiche WebLink
Metadata
Document management portal powered by Laserfiche WebLink 9 © 1998-2015 Laserfiche. All rights reserved.
AWARNING • • • s LumioMAXIMUM AC OPERATING CURRENT:26.62 AMPS <br /> ELECTRICAL SHOCK HAZARD NOMINAL OPERATING AC VOLTAGE: 240 VAC <br /> SOLAR PV SYSTEM EQUIPPED <br /> TERMISIDES ALS ON LINE AND ENERGIZED <br /> AC EL DISLOCATION: WITH RAPID SHUTDOWN <br /> SIDES MAY BE ENERGIZED IN AC DISCONNECT(S),PHOTOVOLTAIC SYSTEM POINT OF <br /> THE OPEN POSITION INTERCONNECTION. <br /> PER CODE(S):NEC 2020:690.54 <br /> LABEL LOCATION: PHOTOVOLTAIC POWER SOURCE <br /> INVERTER(S),AC DISCONNECT(S),AC <br /> COMBINER PANEL(IF APPLICABLE). LABEL LOCATION: <br /> PER CODE(S):NEC 2020:NEC 690.13(B) EMT/CONDUIT RACEWAYS M TURN RAPID SHUTDOWN <br /> &NEC 690.15(C) (PER CODE:NEC690.31(D)(2) SWITCH TO THE"OFF' SOLAR ELECTRIC <br /> PV PANELS <br /> PHOTOVOLTAIC <br /> • • 7406POSITION TO SHUT DOWN <br /> PV SYSTEM AND REDUCE <br /> SHOCK HAZARD IN THE <br /> LABEL LOCATION: <br /> MAIN SERVICE DISCONNECT/UTILITY METER ARRAY. <br /> (PER CODE:NEC 690.13(B)) VERSION <br /> ACDISCONNECT DESCRIPTION DATE REV <br /> LABEL LOCATION: • • • • INITIAL RELEASE 07/19/2023 UR <br /> AC DISCONNECT LABEL LOCATION: <br /> NEC 690.13 B • SOLAR ON OR NO MORE THAT 1 M(3 FT)FROM THE SERVICE DISCONNECTING <br /> ( ) MEANS TO WHICH THE PV SYSTEMS ARE CONNECTED. <br /> LABEL LOCATION: PER CODE(S):NEC 2020:IFC 605.11.3.1(1)&690.56(C) <br /> AWARNING DUAL POWER SOURCE UTILITY SERVICE ENTRANCE/METER,INVERTER/DC <br /> SECOND SOURCE IS PHOTOVOLTAIC SYSTEM DISCONNECT IF REQUIRED BY LOCAL AHJ,OR <br /> OTHER LOCATIONS AS REQUIRED BY LOCAL AHJ. <br /> LABEL LOCATION: PER CODE(S):NEC 2020:690.56(C)(2) <br /> POINT OF INTERCONNECTION <br /> PRODUCTION METER A CAUTION <br /> NEC 705.12(D)(3)&NEC 690.59) <br /> PHOTOVOLTAIC SYSTEM CIRCUIT IS BACKFED CAUTIONWARNING ! <br /> POWER LABEL LOCATION: MULTIPLE SOURCES OF POWER <br /> MSP(PER CODE: NEC 705.12(D)(2)& <br /> CONNECTION NEC 690.59 POWER TO THIS BUILDING IS ALSO SUPPLIED FROM THE PROJECT NAME <br /> • • • RELOCATE <br /> / AWARNING FOLLOWING SOURCES WITH DISCONNECTS LOCATED AS SHOWN <br /> Lo <br /> OVERCURRENT DEVICE Q L0 <br /> LABEL LOCATION: THIS EQUIPMENT FED BY >O <br /> Co C ) CV <br /> SERVICE PANEL IF SUM OF BREAKERS EXCEEDS > ~ DD <br /> PANEL RATING MULTIPLE SOURCES: Q ►� W p <br /> O O <br /> TOTAL RATING OF ALL OVERCURRENT Lu C) <br /> NEC 705.12(6)(3)(2) DEVICES EXCLUDING MAIN POWER J O 6 co Li O <br /> SUPPLY SHALL NOT EXCEED O O p 0 > <br /> NOTES AND SPECIFICATIONS: AMPACITY OF BUSBAR z (:Y) O W W <br /> •SIGNS AND LABELS SHALL MEET THE REQUIREMENTS OF THE O Q N � IL CmC <br /> 2020 ARTICLE 110.21(B),UNLESS SPECIFIC INSTRUCTIONS LABEL LOCATION: Lo 0 <br /> LLI G <br /> ARE REQUIRED BY SECTION 690,OR IF REQUESTED BY THE POINTS OF CONNECTION/BREAKER CC <br /> LOCAL AHJ. G Lr) z <br /> CODE:NEC 705.12(6)(3)(3) O O <br /> •USING EFFECTIVE WORDS,CO ORS AND SYMBOLS.SIGNS AND LABELS SHALL ADEQUELY WARN OF HAZARDS ry p J f�, <br /> •LABELS SHALL BE PERMANENTLY AFFEQUIPMENT OR WIRING METHOD ANDIXED SHALLONOT BE HAND AWARNING THELu , <br /> z � � zLli� <br /> •LABEL SHALL BE OF SUFFICIENT DURABILITY TO WITHSTAND THE DISCONNECTION OF THE Q O LLI <br /> GROUNDETHE ENVIRONMENT INVOLVED. MAY RESULTD N OVE VCONDUCTO ) z OLTAGE O > Q O <br /> •SIGNS AND LABELS SHALL COMPLY WITH ANSI Z535.4-2011, ON THE EQUIPMENT W 0� <br /> PRODUCT SAFETY SIGNS AND LABELS,UNLESS OTHERWISE <br /> SPECIFIED. LABEL LOCATION: <br /> •DO NOT COVER EXISTING MANUFACTURER LABELS. COMBINER BOX (N) PV MODULES <br /> PER CODE:NEC 690.31(E) <br /> (N)200A MAIN SERVICE PANEL <br /> SHEET NAME <br /> WITH (N)200A MAIN BREAKER <br /> (E) UTILITY METER WARNING LABELS & <br /> (N) 60A NON-FUSED AC DISCONNECT PLACARD <br /> (N) ENPHASE IQ COMBINER BOX 4 <br /> SHEET SIZE <br /> 10615 ROSEWOOD AVE ANSI B <br /> 11" X 17" <br /> SHEET NUMBER <br /> PV-5 <br />