Laserfiche WebLink
Lumio <br /> SMART ENERGY TODAY <br /> (SET) <br /> 1550 DIGITAL DR,LEHI,UT <br /> 84043,USA <br /> SYSTEM INFO <br /> (10)Q CELLS <br /> Q.PEAK DUO BLK ML-G10+ <br /> (400W) <br /> (10)ENPHASE <br /> I08PLUS-72-2-US(240V) <br /> DC SYSTEM SIZE:4.000 kWDC <br /> SM■■ : SOLAR STANDARD SYSTEM GROUNDING ' ■ �• SOLAR APPENDIX C ■ 4C SYSTEM SIZE:3.000 kWAC <br /> on■ MOUNT INSTALLATION GUIDE PACE an MOUNT UNIVERSALAF MIDCLAMP INSTALLATION GUIDE : PACE <br /> --------------------------------------------------------------------------------------------------------------------------------------------- --------------------------------------------------------------------------------------------------------------------------------------------- <br /> REVISIONS <br /> WEEBLUs DESCRIPTION DATE REV <br /> ----------- <br /> ___-_— ,Single Use Only i„„ <br /> +- \ REVISION 10/19/2022 A <br /> PROJECT NAME&ADDRESS <br /> ONLY ONE LUG PER ROW OF MODULES: % <br /> Only one lug per row of modules is WEEBLUGCONDUCFOR-UNIRAC P/N 0080025: �- <br /> required. See Page F for additional lugs r�— _ �� Apply Anti Seize and insert a bolt in the aluminum rail and through the clearance hole <br /> required for expansion joints. = in the stainless steel flat washer. Place the stainless steel flat washer on the bolt, <br /> --� oriented so the dimples wiR contact the aluminum rail Place the lug portion on the 1.Position clamp to align T bolt with rail 2.Rotate damp clockwise 2/3 of a tum 3.Slide clamp into position against 4.Place second module. <br /> slot.Lower clamp and insertT•bolt into to engage T-bolt inside rail slot. module. <br /> bolt and stainless steel flat washer.Install stainless steel flat washer,lock washer and O <br /> nut.Tighten the nut until the dimples are completely embedded into the rail and lug. rail slotCN <br /> TORQUE VALUE 10 K los.(See Note on PG.Al 00 <br /> See product data sheet for more details,Modet No.WEEB•LUG•6., <br /> GROUNDING LUG MOUNTING DETAILS: Star Washer is %! (� M <br /> Details are provided for both the WEEB and Ilsco products.The WEEBLug has a stnyle use only �.> z LJ I m <br /> grounding symbol located on the lug assembly.The Ilsco lug has a green colored - f 00 <br /> set screw for grounding indication purposes.Installation must be in accordance — f f (r- < U W CO CA <br /> with NFPA NEC 70,however the electrical designer of record should refer to the � �` N <br /> latest revision of NEC for actual grounding conductor cable size. ttaMitaAtmep,,, L JAq: Q W LJJ m co <br /> Requued 11 not using approved integrated grounding uucruinveter i ura..0 canduam 1 J_ 0 9 <br /> i,u,p,e ra 0n toll LLI U <br /> CD <br /> +-4 AWG:SSin, LLI> Fn <br /> LLI . . OO <br /> AWG a Vn-tin - <br /> GROUNDING LUG-BOLT SIZE&DRILL SIZE Q 1' > _ <br /> GROUND LUG BOLT SIZE DRILL SIZE } Q J <br /> ILSCO LAY-IN LUGCONDLKTOR-UNIRAC P/N 008009P:Alternate Grounding Lug <br /> WEEBLug 1/4- WA-Place in Top SM trail Slot Drill,deburr hole and bolt thru both rail walls per table. S.Tighten bolt and torque to 15 ft-lbs. NOTE:If excessive force is applied in Z � d <br /> ASCO Lug x10-32 7/32' TORQUE VALUE S R lbs.(See Not, step 2,the cap may over-rotate causing Q Q <br /> See ILSCO product data sheet for more details,Model No.GBL-4DIIL it to be mis-aligned with the module J LLI <br /> Torque value depends on conductor size. frame.If this occurs,keep rotating the = <br /> See product data sheet for torque value. cap clockwise until it returns to the 0 <br /> NOTE:ISOLATE COPPER FROM ALUMINUM CONTACT TO PREVENT CORROSION original position. _ <br /> Lf) <br /> N <br /> Cn <br /> r <br /> DATE: 10/19/2022 <br /> SHEET NAME <br /> EQUIPMENT <br /> LSPECIFICATIONS <br /> SHEET SIZE <br /> ANSI B <br /> 11° X 17" <br /> SHEET NUMBER <br /> PV-20 <br />