6617 ASSOCIATED BLVD AMAZON 2023-12-06

Lighting, Motor, and E►rctrical Permit Checklist, Pg. . LTG-CHK 2015 Washington State Energy Code Compliance Forms for Commercial Buildings including R2,R3,R4 over 3 stories and all R1 Revised Nov 2017 Project Title: DSE-1-Everett WA Date 4/30/2020 The following information is necessary to check a permit application for compliance with the lighting,motor,and electrical requirements in the Applicability Location in building Department (yes,no,na) Code Section Component Compliance information required in permit documents Documents Notes LIGHTING CONTROLS Lighting controls, For all lighting fixtures,indicate lighting control method on plans Yes C405.2 E0.03 general for spaces and lighting zone(s)served,or exception taken Luminaire level Indicate on plans all fixtures provided with LLLC in lieu of NA C405.2 lighting controls C405.2 lighting controls;provide description of control (LLLC) capabilities and performance parameters For permanently installed lighting fixtures in dwelling units, NA C405.1 Lighting in dwelling indicate lighting control method on plans for spaces and units lighting zone(s)served,or demonstrate compliance with high efficacy exception C405.2.3 Indicate on plans the method of manual lighting control(whether C405.2.1.1 combined with occupancy sensor,automatic light reduction, Yes C405.2.2.2 Manual controls E1.11-E1.12 daylight responsive or specific application controls),location of C405.2.4 manual control device and area or specific application it serves C405.2.5 C405.2.2.1 Indicate on plans which method of manual 50%lighting load Yes C405.2.2.2 Manual interior light reduction is provided,or whether lighting load is reduced via E1.11-E1.12 C405.2.3 reduction controls occupancy sensors or daylight responsive controls Indicate on plans the method of automatic shut-off control during unoccupied periods(occupancy sensor,time switch or digital E1.11-E1.12 Yes C405.2.2 Method of automatic timer switch)for all lighting zones; shut-off control Indicate locations where automatic shutoff is provided by other methods(occupancy sensor or digital timer switch)or which E1.11-E1.12 time switch control exception applies Indicate on plans the spaces served by occupancy sensors NA C405.2.1 Occupancy sensor Indicate whether occupancy sensor controls are configured to be C405.2.1.1 controls manual-on,automatic 50%-on,or serve a space eligible for automatic 100%-on per exception Occupancy sensor Indicate aisleways and open areas in warehouse spaces NA C405.2.1.2 controls- provided with occupancy sensor controls that reduce lighting " warehouses power by 50% Automatic time switch Indicate locations of override switches on plans and the lighting Yes C405.2.2.1 E1.19-E1.92 controls zone(s)served,include area so.ft. Yes C405.2.6 Digital timer switch Indicate digital timer switch control includes:manual on/off,time E1.11-E1.12 delay.audible and visual indication of impending time-out Indicate primary and secondary sidelight daylight zone areas on plans,include sq.ft.; C405.2.4.2 Daylight zones- Indicate toplight daylight zone areas on plans,include sg,ft. __wV_ NA For small vertical fenestration assemblies(rough opening less C405.2.4.3 Sidelight and toplight than 10 percent of primary daylight zone)where daylight responsive controls are not required,provide fenestration area tc davliaht zone calculation(s) Indicate on plans lighting zone(s)served by daylight responsive controls; Identify sidelight and toplight daylight zones that are not provided with daylight sensing controls and the exception(s)that NA C405.2.4 Daylight responsive apply; controls Indicate on plans the lighting load reduction method- continuous dimming,or stepped dimming that provides at least two even steps between 0%-100%of rated power _` Indicate that daylight sensing controls are configured to • completely shut off all controlled lights in the lighting zone Additional controls Identify spaces and lighting fixtures on plans that require NA C405.2.5 Specific application specific application lighting controls per this section lighting controls Indicate on plans that display and accent lighting,and display C405.2.5- Display and accent case lighting are controlled independently from both general NA Items 1&2 lighting area lighting and other lighting applications within the same AMC Indicate manual and automatic lighting control method 1