DISH Wireless L.L.C. 12/11/2023 - Laserfiche WebLink

GROUNDING NOTES: 1. ALL GROUND ELECTRODE SYSTEMS(INCLUDING TELECOMMUNICATION, RADIO, LIGHTNING PROTECTION AND AC POWER GES'S)SHALL • BE BONDED TOGETHER AT OR BELOW GRADE, BY TWO OR MORE COPPER BONDING CONDUCTORS IN ACCORDANCE WITH THE NEC. r 2. THE CONTRACTOR SHALL PERFORM IEEE FALL-OF-POTENTIAL RESISTANCE CO EARTH TESTING(PER IEEE 1100 AND 81) FOR sh GROUND ELECTRODE SYSTEMS,THE CONTRACTOR SHALL FURNISH AND INSTALL SUPPLEMENTAL GROUND ELECTRODES AS NEEDED TO ACHIEVE A TEST RESULT OF 5 OHMS OR LESS. 3 THE CONTRACTOR IS RESPONSIBLE FOR PROPERLY SEQUENCING GROUNDING AND UNDERGROUND CONDUIT INSTALLATION AS TO wireless PREVENT ANY LOSS OF CONTINUITY IN THE GROUNDING SYSTEM OR DAMAGE TO THE CONDUIT AND PROVIDE TESTING RESULTS. 5701 SOUTH SANTA FE DRIVE 4. METAL CONDUIT AND TRAY SHALL BE GROUNDED AND MADE ELECTRICALLY CONTINUOUS WITH LISTED BONDING FITTINGS OR BY LITTLETON,Co 80120 BONDING ACROSS THE DISCONTINUITY WITH#6 COPPER WIRE UL APPROVED GROUNDING TYPE CONDUIT CLAMPS. 5. METAL RACEWAY SHALL NOT BE USED AS THE NEC REQUIRED EQUIPMENT GROUND CONDUCTOR. STRANDED COPPER CONDUCTORS WITH GREEN INSULATION,SIZED IN ACCORDANCE WITH THE NEC,SHALL BE FURNISHED AND INSTALLED WITH THE POWER CIRCUITS TO BTS EQUIPMENT. 6. EACH CABINET FRAME SHALL BE DIRECTLY CONNECTED TO THE MASTER GROUND BAR WITH GREEN INSULATED SUPPLEMENTAL EQUIPMENT GROUND WIRES.#6 STRANDED COPPER OR LARGER FOR INDOOR BTS; #2 BARE SOLID TINNED COPPER FOR OUTDOOR BTS. 7. CONNECTIONS TO THE GROUND BUS SHALL NOT BE DOUBLED UP OR STACKED BACK TO BACK CONNECTIONS ON OPPOSITE SIDE 1 OF THE GROUND BUS ARE PERMITTED. CAMP+ B. ALL EXTERIOR GROUND CONDUCTORS BETWEEN EQUIPMENT/GROUND BARS AND THE GROUND RING SHALL BE#2 SOLID TINNED ASSOCIATES COPPER UNLESS OTHERWISE INDICATED. 19515 N.CREEK PNWV.SUITE 220 9. ALUMINUM CONDUCTOR OR COPPER CLAD STEEL CONDUCTOR SHALL NOT BE USED FOR GROUNDING CONNECTIONS. BOTHELLwA98011 PHONE.14251240,4392 10. USE OF 90' BENDS IN THE PROTECTION GROUNDING CONDUCTORS SHALL BE AVOIDED WHEN 45' BENDS CAN BE ADEQUATELY www.CAMPASSOC.COM SUPPORTED. 11. EXOTHERMIC WELDS SHALL BE USED FOR ALL GROUNDING CONNECTIONS BELOW GRADE. 12. ALL GROUND CONNECTIONS ABOVE GRADE(INTERIOR AND EXTERIOR)SHALL BE FORMED USING HIGH PRESS CRIMPS. 13. COMPRESSION GROUND CONNECTIONS MAY BE REPLACED BY EXOTHERMIC WELD CONNECTIONS. 14. ICE BRIDGE BONDING CONDUCTORS SHALL BE EXOTHERMICALLY BONDED OR BOLTED TO THE BRIDGE AND THE TOWER GROUND OP' a BAR. a t •, 15. APPROVED ANTIOXIDANT COATINGS('i.e.CONDUCTIVE GEL OR PASTE) SHALL BE USED ON ALL COMPRESSION AND BOLTED GROUND • CONNECTIONS. {O44 ' 16. ALL EXTERIOR GROUND CONNECTIONS SHALL BE COATED WITH A CORROSION RESISTANT MATERIAL. sd foss 17. MISCELLANEOUS ELECTRICAL AND NON-ELECTRICAL METAL BOXES,FRAMES AND SUPPORTS SHALL BE BONDED TO THE GROUND RING, IN ACCORDANCE WITH THE NEC. 18. BOND ALL METALLIC OBJECTS WITHIN 6 ft OF MAIN GROUND RING WITH(1) #2 BARE SOLID TINNED COPPER GROUND CONDUCTOR 19. GROUND CONDUCTORS USED FOR THE FACILITY GROUNDING AND LIGHTNING PROTECTION SYSTEMS SHALL NOT BE ROUTED o< TO ALTER THIS DOCUMENT. EER' THROUGH METALLIC OBJECTS THAT FORM A RING AROUND THE CONDUCTOR,SUCH AS METALLIC CONDUITS, METAL SUPPORT CLIPS OR SLEEVES THROUGH WALLS OR FLOORS.WHEN IT IS REQUIRED TO BE HOUSED IN CONDUIT TO MEET CODE REQUIREMENTS OR LOCAL DRAWN BY: CHECKED BY:APPROVED BY: CONDITIONS,NON-METALLIC MATERIAL SUCH AS PVC CONDUIT SHALL BE USED.WHERE USE OF METAL CONDUIT IS UNAVOIDABLE(i.e., JAC JAC JAG NONMETALLIC CONDUIT PROHIBITED BY LOCAL CODE)THE GROUND CONDUCTOR SHALL BE BONDED TO EACH END OF THE METAL CONDUIT. 20. ALL GROUNDS THAT TRANSITION FROM BELOW GRADE TO ABOVE GRADE MUST BE#2 BARE SOLID TINNED COPPER IN 3/4" REDS REV X: --- NON-METALLIC, FLEXIBLE CONDUIT FROM 24"BELOW GRADE TO WITHIN 3"TO 6"OF CAD-WELD TERMINATION POINT.THE EXPOSED END OF THE CONDUIT MUST BE SEALED WITH SILICONE CAULK. (ADD TRANSITIONING GROUND STANDARD DETAIL AS WELL). CONSTRUCTION 21. BUILDINGS WHERE THE MAIN GROUNDING CONDUCTORS ARE REQUIRED TO BE ROUTED TO GRADE,THE CONTRACTOR SHALL ROUTE DOCUMENTS TWO GROUNDING CONDUCTORS FROM THE ROOFTOP.TOWERS,AND WATER TOWERS GROUNDING RING,TO THE EXISTING GROUNDING SYSTEM,THE GROUNDING CONDUCTORS SHALL NOT BE SMALLER THAN 2/0 COPPER. ROOFTOP GROUNDING RING SHALL BE BONDED TO SUBMITTALS THE EXISTING GROUNDING SYSTEM,THE BUILDING STEEL COLUMNS. LIGHTNING PROTECTION SYSTEM,AND BUILDING MAIN WATER LINE REV DATE DESCRIPTION (FERROUS OR NONFERROUS METAL PIPING ONLY). DO NOT ATTACH GROUNDING TO FIRE SPRINKLER SYSTEM PIPES. A 10/10/2022 ELECTRICAL RDISONS n 10/24/2022 ISSUED FOR EWA 11/07/2022 ISSUED FOR PERMS 2/14/2023 COMMENTS mow THE cm 0/18/2023 REVISED EOMPMERr LOCATION A-9/22/2023 RUED FOR FINAL A R/n/2m ISSUED FOR PR, AkE3 PROJECT NUMBER SESEA00377C DISH Wireless L.L.C. PROJECT INFORMATION SESEA00377C 2930 WETMORE AVENUE EVERETT, WA 98201 SHEET TITLE GENERAL NOTES SHEET NUMBER GN-4 DISH Wireless L.L.C.TEMPLATE KRSION 4S-10/29/2021