Laserfiche WebLink
are available and permuted by UL Electrical Ratings for the IN 1 Fire Input: <br /> SLE-WIR-MODULE Allows your Napco StarUnk device to • Input Voltage 9 25VDC. <br /> connect to the Internet by means of a wireless(Wi-Fi)link, • Maximum Input Current Up to 2mA from FACP NAC crr- <br /> elrminating a wired Ethernet cable connection, Note: cuit <br /> 7AH battery required when using the SLE-WIFI-MODULE. Electrical Ratings for IN 2,IN 3,IN 4,and IN S: <br /> For more information,see WI2191 (Inputs IN 2,IN 3,IN 4,and IN 5 are Class B) <br /> SLE-DLCBL Download Cable,6 feet • Maximum Loop Voltage. 25VDC. <br /> SLE-ANTEXT30 Extended antenna with 30 feet of cable <br /> • Maximum Loop Current. 1.2mA <br /> SLE•ANTEXTSO Extended antenna with 50 feet of cable • End of Line Resistor(EOLR)Value: 1OK(2 req'd) <br /> Electrical Ratings for PGM3 Output: <br /> SLE-ANTEXT75-Extended antenna with 75 feet of cable • Open Collector Output. Maximum Voltage 3V when ac- <br /> SLE•ANTEXTIOO-Extended antenna with 100 feet of cable tive,25V maximum when not active. <br /> (Any suitable external cellular antenna is permitted by UL). • Maximum PGM Sink Current. 50mA(up to 15VDC),25mA <br /> Always follow the manufacturer's installation instructions. (15.1VDC-25VDC) <br /> GEM-Tamperkit - Tamper switches and screws to protect Physical(W x H x D) <br /> • Metal Housing: 11%x 9%x 3%"(29.2 x 24.1 x 8.9cm) <br /> metal housing. • Mounting. Metal housing includes two keyhole slots for <br /> wall mounting(see measurements in W12327) <br /> SPECIFICATIONS Environmental <br /> The following specifications apply to all Start-ink radio models • Operating Temperature: 0'C-49'C(32'F-120°F) <br /> unless otherwise stated. • Humidity. Maximum 93%Non-Condensing <br /> Electrical Ratings for 120VAC,60Ht • Indoor/dry location use only <br /> For Models with Power Supply (SLE-LTEVI-CFBPS & <br /> SLE•LTEAI-CFBPS) <br /> • Input Voltage: 120VAC nonunal <br /> • Input Current:200mA maximum <br /> • Maximum Charging Current: 200mA <br /> Electrical Ratings for.12V/24V <br /> For Models without Power Supply (SLE-LTEVI CFB & <br /> SLE-LTEAI-CF B) <br /> • Input Voltage: 10-25VDC regulated (power-limited out- <br /> put from Listed control panel). <br /> • Input Current, <br /> 10VDC standby: 162mA <br /> 12VDC standby: 125mA <br /> 15VDC standby: 110mA <br /> 24VDC standby: 100mA(Commercial Fire models) <br /> 25VDC standby: 100mA(Commercial Fire models) <br /> WI-Fl Module: (Optional)Add 40mA to the above. <br /> (With peak RF transmission current of 300mA). <br /> NOTICE TO AUTHORITIES HAVING JURISDICTION, USERS, INSTALLERS. <br /> DEALERS.AND OTHER AFFECTED PARTIES <br /> IN <br /> FIRE PROGRAMMING OPTION PERVED UL-ET(YM) <br /> 47(YM) AVAILABLE SETTINGS REOUIRED UL 664 SETTINGS <br /> ULc"E <br /> Jnattended Remote Downloading %o Enable!Usable Disabled(Jumper t installed) Also required for Commercial installations <br /> Unsupervised using conduit within 20 feet of FACP(default) M rot using <br /> N2 IN3.WI and INS Unsupr, Yes Superv4ed!Unsupernsed tondud-install Jumpers 4 and 5 and EOL Resistors. <br /> 200 seconds.5 minutes.6 <br /> 200 seo�nds.5 minutes 60 minutes 6 Hours perntted.n Comrnemal <br /> Day Supervrs+on.Rad o!o NOC minutes.60 mnJtes.6 Fire UL 864 wdh Dual Path enabled <br /> hours 7 days <br /> Tr,-..'IA rn RprlorrIPRv <br /> - <br /> (Annurxaate;Report) Either Path or Both Paths Either Path(annunciation and report of trouble) <br /> WrFi Module Enable1 Usable May be enabled as a primary reporting paC for Fire <br /> 14 <br />