2300 MERRILL CREEK PKY ZAP ENERGY 2024-08-08

BACKWARDS COMPATIBILITY TECHNICAL SPECIFICATIONS (cont'd) The AEGIS 2.0 is backwards compatible and listed for One (1)Abort Circuit use with a full range of conventional detectors and alarm -Compatible with normally open contact-closure type devices as well as suppression accessories from Kidde, devices Fenwal and Chemetron. Going forward, this will allow - Configurable as Class A or Class B legacy panels to be replaced with relative ease. - Supervised for ground faults and open circuits EASY TO INSTALL CABINET - Six (6)Abort Modes available The cabinet design allows for easy installation by fitting - Power-limited between the studs of a standard 16 inch studded wall. It Two (2) Supervisory Circuits is large enough to house two 12 VDC, 12 AH Batteries -Compatible with normally open contact-closure type and provides up to 2 inches (51 mm) of wiring and finger devices space between the circuit board and the cabinet wall. - Configurable as Class A or Class B An optional door design features a Manual Release and - Option to use SUP 1 as fourth detection circuit Abort switch for applications with space constraints. Both - Supervised for ground faults and open circuits switches incorporate guards that prevent their - Power-limited inadvertent activation. Three (3) Notification Appliance Circuits (NACs) TECHNICAL SPECIFICATIONS -Compatible with polarized 24 VDC regulated Audio- Hazards Protected Visual devices • - Rated at 1.5 Amps each - One - Up to 35 synchronized appliances • Power Supply - Configurable as Class A or Class B - 120/240 V, 50/60 Hz (90 to 264 VAC, 47 to 63 Hz) - Supervised for ground faults, shorts, and open AC Main Input circuits -5.4 Amps at 27 VDC Output - Power-limited - Battery capacity up to 68 AH @ 24 VDC - Common NAC/ARC output disable switch -Auxiliary power output rated Class B at 1 Amp at Two (2) Agent Release Circuits 18.8 - 27.6 VDC (resettable) - Each compatible with 1 or 2 control heads, or 1 • Three (3) or Four(4) Detection Circuits actuator/initiator, or 1 FM sprinkler solenoid - Compatible with ESL/Interlogix 700 Series - Circuits electrically capable of simultaneously detectors, CPD-705x, PSD-715x, and THD-705x releasing any combination of two of the above detectors, as well as Normally Open contact devices closure type devices. Refer to documents K-70-100 - Factory configured as Class B and F-70-63 for details on compatibility and the - Supervised for ground faults and open circuits maximum number of devices supported. - Default setting: Power-Limited. Each solenoid on a - Configurable as Class A or Class B power-limited ARC requires the use of an in-line - Supervised for ground faults and open circuits releasing device, P/N 06-220023-001 (order - Power limited separately, not included with panel). - DET 1 and DET 2 used for suppression - Common NAC/ARC output disable switch - DET3/WF configurable for detection or waterflow Four(4) Relays - Option to use SUP 1 circuit as DET 4 circuit* - 3 independently programmable, normally de- • One (1) Manual Release Circuit energized Form-C Relays -Compatible with normally open contact-closure type - 1 dedicated normally energized Form-C Trouble devices Relay - Configurable as Class A or Class B - Relay contacts rated 3 Amps at 30 VDC (resistive) - Supervised for ground faults and open circuits - Power limited • Only contact-closure type, non-powered devices such as switches, pull stations and alarm contacts of 4-wire detectors to be used on this Detector 4 circuit. Powered 2-wire automatic detectors must not be connected to this circuit and the circuit must not be used to power 4-wire detectors. - 4 -