5901 23RD DR W ZAP ENERGY 2024-04-12

GENERAL NOTES: 1. ALL DOORS IN THE CLEAN AGENT HAZARD AREA SHALL HAVE DOOR CLOSURES, DOOR SWEEPS AND DOOR SEALS. (BY OTHERS) 2. THE DISCHARGE TIME OF THE SYSTEM SHALL NOT EXCEED 120 SECONDS. THE PROTECTED VOLUME IS TO BE FLOODED AT A 46.9% CONCENTRATION FOR CLASS "C" ELECTRICAL UP TO 48OV, UNLESS OTHERWISE NOTED ON THE SYSTEM DRAWINGS AND HYDRAULIC CALCULATIONS. THE HAZARD AREA SHALL MAINTAIN DESIGN CONCENTRATION FOR A MINIMUM OF 10 MIN. 3. THE CLEAN AGENT CONTROL PANEL SHALL HAVE BATTERY BACK-UP TO PROVIDE 24 HOURS OF STANDBY OPERATION WITH 5 MINUTES OF ALARM UNLESS NOTED OTHERWISE ON THE DRAWINGS AND THE BATTERY CALCULATIONS. 4. INTERLOCK WIRING AND CONDUIT TO CONNECT TO THE REMOTE FIRE ALARM SYSTEM (IF REQUIRED) SHALL BE PROVIDED BY OTHERS. SUPPRESSION SYSTEMS INC. WILL PROVIDE RELAY CONTACTS LOCATED IN THE CLEAN AGENT CONTROL PANEL. 5. INTERLOCK WIRING AND CONDUIT TO EQUIPMENT SHALL BE PROVIDED BY OTHERS. SUPPRESSION SYSTEMS INC. WILL PROVIDE RELAY CONTACTS LOCATED IN THE CLEAN AGENT CONTROL PANEL. 6. THE CLEAN AGENT HAZARD AREA SHALL BE SEALED TO PREVENT LEAKAGE OF THE AGENT. (BY OTHERS) SUPPRESSION SYSTEMS INC. WILL PROVIDE GUIDANCE AND/OR SUPERVISION. 7. THE 120VAC CIRCUIT FOR THE CLEAN AGENT CONTROL PANEL SHALL BE A DEDICATED CIRCUIT WITH A LOCK -OUT DEVICE ON THE BREAKER SWITCH TO COMPLY WITH NFPA 72 CURRENT ADDITION. 8. ALL TERMINATION'S IN THE CLEAN AGENT CONTROL PANEL SHALL BE PERFORMED BY SUPPRESSION SYSTEMS INC. 9. RETENTION TIME FOR THE PROTECTED SPACE SHALL BE VERIFIED BY A ROOM INTEGRITY TEST PERFORMED IN ACCORDANCE WITH NFPA 2001 2018 EDITION. CLEAN AGENT PIPING SYSTEM NOTES: 1. REFER TO SYSTEM DRAWINGS AND CALCULATIONS FOR THE LOCATION AND LAYOUT OF THE CLEAN AGENT DISTRIBUTION PIPING SYSTEM. EXAMINE THE CONFIGURATION OF THE PIPING SYSTEM TO ENSURE THE PIPING AND DISCHARGE NOZZLES DO NOT INTERFERE WITH ANY ON SITE PHYSICAL OBSTRUCTIONS WITHIN THE CLEAN AGENT HAZARD AREA BEFORE THE PIPING INSTALLATION BEGINS. SHOULD ANY CONFLICTS OCCUR NOTIFY SUPPRESSION SYSTEMS INC. TO MAKE THE REQUIRED ADJUSTMENTS TO THE SYSTEM DRAWINGS AND HYDRAULIC CALCULATIONS PRIOR TO BEGINNING PIPING INSTALLATION. ANY DEVIATIONS IN THE ROUTING OF THE PIPE NETWORK SHALL BE VERIFIED AND APPROVED BY SUPPRESSION SYSTEMS INC. 2. CLEAN AGENT SUPPRESSION SYSTEM SHALL BE INSTALLED AND TESTED IN ACCORDANCE WITH NFPA 2001 CURRENT ADDITION, AS WELL AS ALL APPLICABLE LOCAL CODES. DO NOT HYDROSTATIC TEST. PNEUMATIC PRESSURE TEST WITH AIR OR N2 TO 40 PSI FOR 10 MINUTES. AT THE END OF 10 MINUTES SHALL NOT DROP BELOW 20% OF THE TEST PRESSURE. 3. PIPING MATERIAL MUST CONFORM TO THE REQUIREMENTS OUTLINED IN NFPA 2001, CURRENT EDITION. SCHEDULE 40 OR SCHEDULE 80 PIPE (BLACK OR GALVANIZED) MUST CONFORM TO ASTM A53 OR A106. ORDINARY CAST IRON PIPE, STEEL PIPE CONFORMING TO ASTM-120, OR NONMETALLIC PIPE SHALL NOT BE PERMITTED TO BE USED. 4. PIPE FITTINGS MUST CONFORM TO THE REQUIREMENTS OUTLINED IN NFPA 2001, CURRENT EDITION. MALLEABLE IRON FITTINGS (BLACK OR GALVANIZED) SHALL BE 300 LB. CLASS THAT CONFORM TO ASTM SPECIFICATION A-197. 150 LB. CLASS FITTINGS AND ORDINARY CAST IRON FITTINGS ARE NOT PERMITTED. ONLY LISTED GROOVED, THREADED, WELDED OR FLANGED FITTINGS MAY BE USED, PROVIDED THEY CONFORM TO THE ABOVE REQUIREMENTS. HOLE CUT FITTINGS MAY NOT BE USED. 5. ALL PIPE JOINING METHODS SHALL BE IN ACCORDANCE WITH NFPA 2001 CURRENT ADDITION. TEFLON TAPE IS RECOMMENDED AND SHALL BE USED WITH ALL THREADED PIPING CONNECTIONS. THREADED PIPE AND FITTINGS SHALL BE TAPERED IN CONFORMANCE WITH ANSI SPECIFICATION B-20.1. ALL GROOVED PIPING CONNECTIONS SHALL BE BE LUBRICATED PER MANUFACTURERS SPECIFICATIONS. 6. ALL PIPING MUST BE RIGIDLY SUPPORTED BY A COMBINATION OF PIPE HANGERS AND RIGID SUPPORT BRACKETS. PIPE HANGERS ARE USED TO SUPPORT THE "DEAD LOAD" OF THE PIPING SYSTEM AND SHALL BE SPACED AT INTERVALS NOT EXCEEDING 15 FEET. RIGID SUPPORTS ARE REQUIRED TO SUPPORT THE "LIVE LOAD" OF THE PIPING SYSTEM DURING DISCHARGE. RIGID BRACING IS REQUIRED AT EACH DIRECTIONAL CHANGE - 90° ELBOW, TEE AND NOZZLE. ALL 180" NOZZLES REQUIRE BACK -BRACING IN THE OPPOSITE DIRECTION OF THE DISCHARGE PATTERN. EARTHQUAKE BRACING SHALL BE USED WHERE REQUIRED BY LOCAL CODE. REFER TO ANSI B31.1 FOR BRACING REQUIREMENTS. 7. REDUCTIONS IN PIPE SIZE SHALL BE DIRECTLY AFTER A TEE WITH THE TEE BEING THE SAME PIPE SIZE AS THE INLET LINE TO THE TEE. REDUCTIONS IN PIPE SIZE MAY ALSO BE MADE USING A CONCENTRIC BELL REDUCER AFTER A UNION, PROVIDED THE NEXT CHANGE IN DIRECTION (TEE) IS LOCATED A MINIMUM OF 10 PIPE DIAMETERS DOWNSTREAM OF THE CONCENTRIC BELL REDUCER. CONCENTRIC BELL REDUCERS OR CONCENTRIC REDUCING COUPLINGS SHALL BE USED TO MAKE ALL REDUCTIONS IN PIPE SIZE. REDUCING BUSHINGS, WELD-O-LETS AND HOLE CUT FITTINGS SHALL NOT BE PERMITTED. 8. THE SYSTEM SHALL BE INSTALLED IN A PROFESSIONAL MANNER WITH "GOOD COMMERCIAL PRACTICE". ALL PIPING AND FITTINGS MUST BE REAMED, BLOWN CLEAN AND SWABBED WITH A CLEANING SOLVENT TO REMOVE DIRT, RUST AND OIL. 9. PIPE REDUCTIONS MADE DIRECTLY AFTER A CHANGE IN DIRECTION, WITH THE FITTING BEING THE SAME PIPE SIZE AS THE INLET, SHALL BE MADE USING A COMMON CONCENTRIC BELL REDUCER. REDUCING BUSHINGS ARE NOT ACCEPTABLE (UNLESS OTHERWISE NOTED). A MINIMUM OF 10 PIPE DIAMETERS MUST BE MAINTAINED FROM THE CENTER OF THE FITTING TO THE CENTER OF THE NEXT CHANGE IN DIRECTION. 10. WHEN BRACING THE PIPING CARE SHOULD BE TAKEN TO INSURE THE NOZZLE LOCATIONS ARE WITHIN ONE FOOT OF THE LOCATIONS SHOWN ON THE SYSTEM PLANS. CORRECT NOZZLES SHALL BE INSTALLED EXACTLY IN ACCORDANCE WITH THE SYSTEM PLANS. NOZZLES SHALL BE INSTALLED PERPENDICULAR TO THE CEILING FOR PROPER DISTRIBUTION PATTERNS. 180° NOZZLES SHALL BE ALIGNED WITH THE ORIFICE HOLES ORIENTED PARALLEL TO THE ADJACENT WALLS SO NO DIRECT WALL IMPINGEMENT OF THE AGENT OCCURS. 11. FINAL INSTALLATION ACCEPTANCE SHALL BE IN ACCORDANCE WITH NFPA 2001 CURRENT ADDITION. ELECTRICAL SYSTEM NOTES: 1. THE DETECTION AND CONTROLS PORTION OF THE FIRE PROTECTION SYSTEM SHALL BE INSTALLED IN ACCORDANCE WITH NFPA 70,72 AND STATE AND LOCAL CODES WHERE APPLICABLE. 2. ALL WIRING AND CONDUIT FOR THE FIRE PROTECTION SYSTEM SHALL BE INSTALLED IN MINIMUM OF 1/2" RACEWAY, IN ACCORDANCE WITH THE CURRENT REQUIREMENTS OF THE NATIONAL ELECTRICAL CODE (NFPA 70), NATIONAL FIRE ALARM CODE (NFPA 72), CITY, STATE, LOCAL BUILDING CODES, THE AUTHORITY HAVING JURISDICTION, PROJECT SPECIFICATIONS AND THE MANUFACTURE'S RECOMMENDATIONS. 3. ALL WIRING SHALL BE INSTALLED USING INSULATED INDIVIDUAL CONDUCTORS IN CONDUIT. THERE SHALL BE NO BUTT SPLICING. ALL WIRE RUNS BETWEEN PANEL AND/OR DEVICES SHALL BE MADE WITH A SINGLE LENGTH OF WIRE. CONDUCTORS ARE TO BE COLOR CODED, NUMBER CODED OR BOTH TO IDENTIFY THE CIRCUITS AND POLARITY. ALL WIRING SHALL COMPLY WITH ARTICLE 760 OF THE NATIONAL ELECTRICAL CODE AND THE MANUFACTURER'S RECOMMENDATIONS. 4. REFERENCE MOUNTING INSTRUCTION INCLUDED WITH EACH DEVICE. 5. LOW VOLTAGE CIRCUITS MUST NOT BE COMBINED IN CONDUITS WITH HIGH VOLTAGE (120, 240, ETC. VOLT) AC POWER OR CONTROL CIRCUITS, SUCH AS FAN SHUTDOWN, EQUIPMENT SHUTDOWN, ETC. 6. ROUTE NON -POWER LIMITED WIRING AT LEAST 1/4 INCH AWAY FROM ALL POWER LIMITED WIRING. DO NOT ATTACH POWER LIMITED AND NON -POWER LIMITED WIRING TO THE SAME TERMINAL BLOCK. 7. MINIMUM CONDUCTORS TYPE AND SIZE REQUIREMENTS: 7.1. DETECTION CIRCUITS - 16 AWG THHN OR EQUAL 7.2. NOTIFICATION APPLIANCE CIRCUITS - 16 AWG THHN OR EQUAL 7.3. RELEASE CIRCUITS - 16 AWG THHN OR EQUAL 7.4. 24 VDC POWER CIRCUITS - 14 AWG THHN OR EQUAL 7.5. 120/240 AC POWER CIRCUITS - 14 AWG THHN OR EQUAL 7.6. ALL CONDUCTORS MUST MEET THE MINIMUM RATING OF 600 VOLTS AT 90° C. 8. ELECTRICAL EQUIPMENT/SYSTEMS SHALL BE INSTALLED IN ACCORDANCE WITH GOOD COMMERCIAL PRACTICE. CARE SHALL BE TAKEN TO AVOID INCORRECT WIRING, CONNECTIONS, FAULTY FABRICATION AND/OR IMPROPER INSTALLATIONS. ALL CONDUIT SHALL BE RIGIDLY SECURED. 9. AC AND DC CURRENT SHALL BE RUN IN SEPARATE CONDUIT AND BOXES. 10. PAINT ALL J-BOXES AND COVERS RED TO IDENTIFY FIRE PROTECTION SYSTEM. 11.IDENTIFY EACH COVER WITH POWER LIMITED FIRE ALARM CKT. 12.MAINTAIN 1" SEPARATION BETWEEN ALL POWER LIMITED AND NON POWER LIMITED CIRCUITS. 13. CONTROL SYSTEM SHALL BE INSTALLED AND TESTED IN ACCORDANCE WITH NFPA 72, AS WELL AS ALL APPLICABLE LOCAL CODES. EXCLUSIONS: **WORK LISTED BELOW SHALL BE PROVIDED BY OTHERS OR UNDER OTHER SECTIONS OF THE PROJECT.- 1 . 120 VAC POWER SUPPLY TO THE CLEAN AGENT CONTROL PANEL. 2. INTERLOCK WIRING AND CONDUIT FOR SHUTDOWN OF HVAC, DAMPERS AND/OR ELECTRIC POWER SUPPLIES, RELAYS, SHUNT TRIP BREAKERS OR OTHER DEVICES. 3. CONNECTION TO LOCAL OR REMOTE FIRE ALARM SYSTEMS OR LISTED CENTRAL ALARM STATION. 4. ALL MATERIALS AND LABOR TO ENSURE THE "AIR -TIGHTNESS" OF THE PROTECTED SPACE(S) AND RESPONSIBILITY FOR THE INTEGRITY OF THE CLEAN AGENT PROTECTED SPACE TO SATISFY THE REQUIREMENTS FOR THE TEN (10) MINUTE RETENTION TIME. SUPPRESSION SYSTEMS INC. MAY PROVIDE ASSISTANCE, BY MEANS OF INSPECTION OF THE SPACE AND MAKING RECOMMENDATIONS ON REMEDIAL ACTIONS THAT MAY BE REQUIRED TO ENSURE ROOM INTEGRITY. PROJECT STANDARDS: APPLICABLE CODES: NFPA 2001 2018 NFPA 70 2017 NFPA 72 2019 INTERNATIONAL FIRE CODE 2018 INTERNATIONAL BUILDING CODE 2018 SCOPE OF WORK: PROVIDE A SINGLE ZONE CLEAN AGENT (IG-100 INERT GAS) FIRE SUPPRESSION WITH ADDRESSABLE DETECTION AND CONTROLS TO PROTECT CAPACITOR ROOM. THE MEASURE 20'-0" X 24'-0" X 9'-9"' WITH A V4, SUB -FLOOR. THE SYSTEM IS DESIGN TO PROTECT A CLASS "C" FIRE HAZARD. STANDARD DETECTOR SPACED AT 250 SQ. FT. SHALL RELEASE THE SYSTEM. ALARM, TROUBLE AND SUPERVISORY TO BUILDING FACP BY SSI. OWNER / SITE DATA: ZAP ENERGY 5901 23RD DRIVE WEST EVERETT, WASHINGTON 98203 AUTHORITY HAVING JURISDICTION: CITY OF EVERETT 3200 CEDAR STREET EVERETT, WA 98201 PHONE: 425-257-8810 PARCEL NUMBER: 2964965 DRAWING INDEX FP-01 NOTES AND DRAWING INDEX FP-02 GENERAL ELEVATION AND MAPS FP-03 PARTS LIST AND SEQUENCE OF OPERATIONS FP-04 FLOOR PLANS AND ISOMETRICS FP-05 ELECTRICAL MULTI -LINE WIRING DIAGRAM FP-06 ELECTRICAL DETAILS AND SINGLE LINE DIAGRAM FP-07 MECHANICAL DETAILS SUPIdESSION SYSTEMS INC. SPECIAL HAZARDS FIRE PROTECTION SIM 20TH STREET EAST, SUITE B FIFE, WA 98424-1798 TM (253) 9263300 FAX (253)9263306 LOGO'S fKidde Fire Systems PROTECTION ENGINEERS STAMP COMPLIANCE SUBMITTALS DATE 100% SUBMITTAL 02/08/23 REV DESCRIPTION DATE QREVIEW COMMENTS 02/17/23 0 ZL 0 co z Q w J U 0 0 LU W z O N 00 O) < Lu Lu Ir 0 > W Cc C/) O 0 U IL U Z. w 9 z w U) w w LL z w o Lu H 07 Fz LU W �: o C) Ir o z w a N � a ( (� N 0) U7 DESIGNED BY: NMB SCALE: NOT TO SCALE UNLESS NOTED OTHERWISE DRAWNBY: NMB CHECKED BY: ZST JOB NUMBER: 2306 SHEET TITLE: FIRE PROTECTION DRAWINGS NOTES AND DRAWING INDEX SHEET NUMBER: FP-01 of 07